-
Similar Forum Topics
-
By DarkRider
This is something I'm extremely curious about. Has anyone ever attempted to buy a quad (or any other vehicle) from an impound lot? I've always wondered if this could be a bargain, or a waste of time. Google searches do turn up some helpful results. Looks like the state of NJ holds auctions online which I'd be a bit hesitant about.
My online searches haven't really turned up any results of anyone buying an ATV this way. I'd be really curious if anyone tried this, or knows someone who has. I've actually found a couple pages with online auctions for my state, but none had ATVs.
-
By Frank Angerano
So I decided to pick up a small trailer if I could get one for the right price. I found this one for a few hundred bucks on Craig’s list. It is a galvanized trailer which is exactly what I was looking for. The wood was shot and needed some minor repairs which I could care less about as long as the chassis was good.
I striped it down and put a new deck on. I had some vinyl realtree graphics that I had laying around so I added them to the fenders which I think worked out well. Very happy with this little guy.
I'm having the iron workers at my jobmake me up a few lightweight side rails that will have a 22 degree bend in them to accommodate the tires that slightly hang over the edge and will incorporate some tie down points as well.
-
By kawasig
Hello All
I'm kinda new to ATVs. I just bought a 1987 Suzuki quad runner 230 Dual Range. I'm having a problem finding info on it. It's very clean, only 2.800 miles. The front wheels are only 30 in.center to center. I was thinking about adding wheel spacers to give it more stability. I realize the added stress on ball joints and bearings. I'm wondering if there are any other concerns? Any input is greatly appreciated!
-
By StayTheTrail
Hey everyone!
Ya'll have been so great and welcoming to our new Ambassador program, we wanted to be sure that Quad Crazy was getting info directly from us about the Stay The Trail educational program too.
The program was started in 2003 with the purpose of educating the public about responsible trail use and fostering a sense of stewardship among OHV enthusiasts.
The "Where To Go" section of our website is another great resource for anyone looking for trail info. We host all of the Motor Vehicle Use Maps (MVUM) and overlay them on the Google mapping system. We want this site to be the place you go to for trail maps as you plan a run. The MVUM maps show what trails are open for what types of vehicles. If a trail is not on these maps, it is not an open trail.
We attend events and set up at trailheads throughout the season to ensure that folks are getting the info and education they need to be responsible on public trails. We have posters and brochures that quickly review these guidelines (all of the Etiquette info can also be found on the website).
Very soon, we will have a HUGE announcement about mobile mapping options!
Sam and Matt are going to be around on the forum, keeping everyone updated on what is new with the program and answering questions. Feel free to ask us any questions!
Oh – and don’t forget to follow us on FACEBOOK!
-
By PolarisRich
I thought I would make a quick "How-to" on setting wheel alignment since I was flipping my tie rod ends and I was going to have to re-align the wheels anyways.
Here's some of the tools you will need...
1.) Start with the ATV on a smooth and level surface, like a cement garage floor or driveway.
2.)Center up (Eyeball It) the handle bars and lock them into place with 2 ratchet straps, one on each side of handle bars. This of course prevents them from moving when your adjusting the tie-rods.
3.) Place two Jack Stands approximately 2 feet in front of the atv even with the outside edge of the two front wheels.
4.) Wrap a length of string all the way around the ATV and Jack Stands, Start and end at the rear hitch. Make sure the string is the same height from the ground on all 4 wheels. I like to attach a few elastic bands to both ends of the string before attaching the string to the hitch. This makes it easier to adjust the strings when moving the Jack Stands.
4.) Break lose the inner and outer tie-rod nuts. NOTE! Make sure you use 2 wrenches, one on the nut and one on the ball joint. Damage can occur by only using one wrench.
5.) Adjust the string by moving the Jack Stands in or out untill the string just touches both of the side surfaces of the rear tires on each side of the ATV. This will take some time to get it right but it needs to be done!
Check manufacturers wheel alignment specifications on your specific make and model before you adjust any components.
For this wheel alignment I'm using the Polaris Specs which seems to be a common setting.
Polaris - The recommended toe alignment is 1/8″ to 1/4″ toe out. This is a total amount, not per wheel.
6.) On the front rim, measure the distance from the string to the rim at the front and rear edges of the rim. The rear measurement should be 1/16″ - 1/8″ (.2 to .3 cm) more than the front measurement.
7.) If an adjustment is necessary, Turn the tie rod itself with a wrench or your hand in small increments. It doesn't take much to move the tire a long way, so go slow. Keep re-checking your measurement's until you have a 1/16″ - 1/8″ differance to the string.
6.) Once your satisfied that you have the correct "Toe Out" measurements you can tighten up the inner and outter tie-rod nuts on both sides. AGAIN...make sure to use 2 wrenches.
7.) Now take your ATV for a test drive to test your adjustments. If it still pulls one way or the other, just repeat the above steps to tweek the adjustments again utill your happy.
The whole process only takes about 15-20 min.
-
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.