Quantcast
Jump to content

Recommended Posts

Posted

Hi everyone new to the site, but like it alot. I got a problem starting my quad, Ive got good spark, full battery, and fresh gas but it wont start. The starter is working properly, and I can pull/roll start it fine. The thing runs perfect once started no idling problems, but even after its warmed up if I shut it off it still wont start without pulling it. Any advice would be greatly appreciated.

Posted

if you can jump start it fine i will guarente that it is your valves.. the z's valves need to be checked and reshimmed often. what happens it they will cup and get worn and will decresse in clearence.. get the feeler gauge out and check your clearances. im beting they will be zero.

Posted

Sometimes the battery just doesn not have enough juice to cank the motor fast enough, but appears good...like Bot said. Try the jumper back.

Are you getting fuel and spark when you hit the starter button?

Posted
If the valves were that far out of whack it would not idle fine or run fine. But it is still worth checking.

alrighty then.. i have seen it happen more than once.... z's are notorious for this issue..

Posted

Thanks for the input everyone, I checked the valves and there right on, however when I pulled the spark plug to check them I found water, so Im waiting for a new head gasket right now. Should be here in a couple of days, ive got the battery charging till then, So Ill let you know.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Forum Topics

    • By rjsummer
      Just picked up an 84 LT185 ATV, I understand there was an accessory add  on that gave it electric start, anyone have any info about that kit? 
    • By Rockbottom
      2008 400 big bear was running now will not start
      have power to relay, in neutral, press start have power to starter but nothing happens starter does not turn
      i have good ground at battery to frame and added ground from wire harness to frame beside batter/ frame ground
      blue white wire to cdi has power with key on
      I believe the neutral lock out is working since is was before i shut it down
      if i put  it in gear and hit the start button with key on the relay does not click or send power the starter
      The 3 wires at the relay have power with key on
      What should i test next?
      thanks ahead
    • By Mister907
      Hi guys, I have a 2004 big bear 400. Last winter while plowing the driveway, I heard a loud pop from the left side of the engine. It continued to run as I looked for leaky fluid, but then died shortly after backing it up and won’t start now. The oil light comes on when I try to start it, no noise or anything else. 
      No blown fuses that I can find.
    • By LMI
      Hi all.  New to the forum & quads.  Seems like a great place full of info.
      I just recently picked up a 2005 Suzuki KingQuad LTA700.  I need a battery.  I've been reading up on conventional vs AGM types.  I have a Royal Distributing and Canadian Tire.  RD has 2 types avail for my year/Model a battery YTX16-BS CRANK $75, and BATTERY YTX20CH-BS YUASA $140.  Neither of these is the type from the manual FTZ16-BS.
      from what I can tell... I think the only difference is the capacity with the $75 unit rated at 14 AH/10HR and the $140 unit rated at 18 AH/10HR ... which is the rating in the manual for the FTZ16-BS.  How much does this make a difference for nearly x2 the cost?
      And about the models/type numbers.... what is important to know ... they all end in "-BS" but are the other details relevant or just manufacturer naming?
    • By Jdeaton011989
      Hi all. I have a timberwolf 250 2nd that will not start.. I thought it was out of time bc the guy I got it from said it just quit on him. The tensioner had a nut welded to it and it was like2 teeth off. I installed new tensioner and chain and it still will not start. It has fire and it will not hit off brake cleaner. It has compression. Haven't put a gauge but I'm sure it will crank and run with what it has. I double checked my work and it's still in time. Spot on. Both valves move. I'm about to put a feeler gauge on them and I'll cone back but other than that any ideas?
×
×
  • Create New...