-
Similar Forum Topics
-
By Randel1
I recently read an article about restoring or at least improving the looks of faded and discolored plastic body parts. In the article it suggested using a 50/50 mixture of boiled linseed oil and paint thinner. You mix it up and apply it with a brush or rag to rub it in and remove the oxidation. I curious to find out if anyone has had experience with doing this and what was their short/long term results of doing so. I would hate to try it and find out that a few weeks/months down the road my plastic body parts self destruct.
-
By Suzukiquad
Hi, I have been around everything with a motor since I was little, and finally purchased more to get my husband, and kids involved. I have 4 quads I will be searching around for information on. I have two 2002 Suzuki LT80K quads, a 1997 Yamaha Timberwolf 250, and a 1996 Kawasaki Bayou 220. I have had different ones throughout the years, and plan on buying another Yamaha Banshee. I plan on trying to learn more about all of them, so I can customize some of them. I know nothing about them besides how to race them, my dad always took care of the rest, but figured it was time for me to learn.
-
By kawasig
Hello All
I'm kinda new to ATVs. I just bought a 1987 Suzuki quad runner 230 Dual Range. I'm having a problem finding info on it. It's very clean, only 2.800 miles. The front wheels are only 30 in.center to center. I was thinking about adding wheel spacers to give it more stability. I realize the added stress on ball joints and bearings. I'm wondering if there are any other concerns? Any input is greatly appreciated!
-
By Kaz
Troubleshooting a no spark issue, was running OK, maybe a little rich, turned it off, now no spark. I've checked/ohmed out the main key switch, the start/stop switch, neutral switch, brake switch - all good. It will crank the starter, but no spark with the starter or when I try the pull start. I've checked all fuses and diodes. Swapped battery. New plug. New coil. Swapped in a used CDI - no help. Traced, removed, cleaned, reattached all grounds. Removed things like my winch from the circuits to be sure a bad relay or something was dragging it down. When testing voltages, the orange wire going from the CDI to the ignition coil shows no/very low voltage-shouldn't it have 12V on it? Sometimes I get a very weak, intermittent glow on my spark tester, but not enough to fire the plug. I've checked continuity on just about all wires in the harness. Checked/cleaned/lubed w dielectric grease- all connections, redid a few that looked old/dirty. I've checked the stator resistances, all good, but have a stator and rectifier ordered anyway, will arrive Sunday. I verified that the rectifier has a voltage output back to charge the battery while cranking - 10.5-11V, low, but expected while starter is engaged. What else can I check as part of troubleshooting? I have a Haines service manual, but the 1999 350 4x4 seems to be an odd model, there isn't an exact electrical diagram for it, but found one for another year that has all the same number of wires and same color wires, so I've referenced that. Any hints, tips or advice would be appreciated! Thanks!
-
-
By fwsamm
Im aware that this relay needs a positive (+) and a negative (-) to activate the other side. The blue wire is the neutral wire so when in neutral it gets ground. The green wire is from the parking break; when you pull the break in it gets ground (-). however one of those two needs to be neutral so that the positive from kill switch can go to the starter relay. The ground from the starter relay is from the start switch. Which one (neutral or parking break) should have a positive (+) voltage?
-
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.