Quantcast
Jump to content

Recommended Posts

Posted

Ok got the atv running like a champ just need a battery......but wait i look on the floor and gas is all over the floor......the gas was leaking from the intake..and out of the hose leading from the float bowl....plz help...oh yea ima put a video up......yea sooo:aargh:

Posted

its a chinese quad.....ummmm...on the plastics it says 200st........all chinese engines r the same.... but the sizez of frame r differnt and diffrent ccs

Posted

I changed the title to try and be as descriptive as possible with the info given.

I agree 100% with Bot, that sounds like a stuck float to me too. I would take the carb apart and check the float adjutment and for any debris that may be causing the float needle to hang up.

  • 7 months later...
Posted

ck.for stuck needle valve,needle not seeting proper ,hole in float,bleed screw loose in bottom of carb,if no one has messed with carb,do not try to reset float,it was set at factory to close the needle valve as the gas feels up the carb bowl,they dont unset them selves,

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Popular Now

  • Similar Forum Topics

    • By LCP92
      Guys, I've got a 1999 Honda Foreman 450S.  It runs great, but smokes out the exhaust after startup until it warms up.  I'm thinking the valve seals are leaking.  I was wondering if there is a way to replace them without removing the head or if there's an oil additive that will recondition the rubber seals.  Any advice?
    • By PupATV
      Hey guys! I am new here to the forum and need some help getting my Polaris 325 Magnum 2001 Running.....So I got it for free and it has never run quite right...I put a aftermarket carb on it last year and it was running fine but it only went like 20 maybe 25mph max......But then the needle and seat sealed leaked within a yeah and it flooded it REALLY bad so I changed the oil because it was full of gas. So then I put a genuine Polaris carb on it and I have it set to all the factory specs, but it was still not running right....So I replaced the ignition coil and the spark plug and that solved one of the problems I had (It would bog down and stop running when i would go up a hill) But it still didn't have that much "Punch" to it like my Kawasaki Prairie 300 ans Suzuki Kingkuad 300.....So I replaced the CDI but it's still not running right! It's acting like it rich kinda....So it runs mostly okayish when I have the airfilter on but the top of the airbox off but as soon as I put the airbox lid on it like REALLY bogs down and wants to stall really bad. I have the carb at the factory specs and it has a pretty new fuel pump so I have no ideas whats going wrong! It still nly has a top speed of only about 30-35mph and it sounds like it's choking the whole time! Thank you for sticking to the end, and I hope you guys can help me!
      -PupATV
    • By bhristianzx12
      I have acquired a free 92 Polaris 350L 4X4. Ive replaced carburetor from ebay, replaced spark plug, im trying to pull start but sounds like it doesnt want to fire. Spark is a bright orange spark (checked with spark plug tester), replaced plug, pre mixed gas from an external gravity feed tank. Compression test good. Anyone got any recommendations for me?
    • By Travis_Smith
      I have a 2002 Kawasaki Prairie KVF 400 and im trying to figure out the actual float height... i have read 17mm +- 2mm, seen 13mm and 23mm... what is happening is it will start right up, rev a little and all is fine, when it warms and you put a load on it bogs down and sputters. no i don't have a manual
    • By DPDISXR4Ti
      I hadn't driven my Kodiak for a two months, and since it was low on fuel, the first thing I did was filled it up to maybe 7/8 full. Getting ready to start it, I rotated the fuel selector switch to "on" and within seconds I smelled and saw fuel dripping onto the floor. I quickly turned it off and the fuel gradually stopped - I can repeat this.
      The fuel is flowing from the hose that is connected to the bottom of the carb, and routes around to the left side toward the wheel well. Any idea what's going on here? It ran fine the last time I had it out.
      Thanks...
×
×
  • Create New...