Quantcast
Jump to content

Width of the rear axle bars

Mandy

By Mandy
in Yamaha ATV Forum

 Share

Recommended Posts

Mandy Apprentice

Mandy

Posted
Posted

Hi Guys Ive been racing for a while now but I've noticed that the bikes I race against seem to have a wider axle not sure if thats the right term then the one I currently have on. Now wen I take corners my bike always lifts up instead of being flush. Should I change my width on the rear axle? :confused:

DirtDemon Veteran

DirtDemon

Posted
Posted

A wider alxe will definately help you stay flat around corners. Wider front a-arms would help too, but it is best to run aftermarket shocks, or have your stock ones re-valved and re-sprung to compenstate for the leverage difference created by the longer a-arm.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Forum Topics

    • HoldenBoy
      Starter not staying engaged while cranking
      By HoldenBoy
      Hi all,
      Looking for some help on a starter/bendix issue. Can Am outlander 450 2017. While cranking to start, the starter spins and engages into the ring gear. After a few seconds the bendix retracts while still spinning and there is no damaged teeth on the drive pulley.
    • BillR94
      1998 Polaris Magnum 425 starts but dies right away.
      By BillR94
      I picked up this ATV that had no spark. The previous owner said he was driving it and it died and would not start. He discovered it had no spark. He replaced the CDI and the coil with no luck. He got tired of it and I bought it. I replaced the stater and now it has strong spark. Now, it starts for a second or two then dies. It will not stay running. I have checked the timing and it is spot on. The valves are adjusted correctly. I see no warn issues with the cam. I put the original CDI and coil back on it. Same problem exists. Compression is at 65 psi (has decompression mechanism),
      I took off the muffler in case the issue was clogged pipes. No change. I replaced the spark plug. No change. The carb was an aftermarket so I put a Niche carb on with no change. I bypassed the fuel pump and that did nothing to solve the problem. 
      I don't know if this is a carb issue or an ignition issue. I am looking around locally for an OEM carb to try out but not sure that will fix the problem. 
      Can anyone help me solve this problem. I am running out of ideas. 
      Thank you for your time
      Bill
       
    • wjmedic
      2003 Polaris Sportsman 400 - Right front tire will not disengage from AWD
      By wjmedic
      Recently rebuilt front end on this Polaris 400. New axles, bearings, seals, control arm bushings, Hilliard clutch thoroughly cleaned and inspected with no damage noted. 
      Everything put back to together. Placed bike on jack stands all four wheels off the ground, started in 2 WD switched to AWD both front tires spinning, when AWD turned
      off right front wheel will not disengage from AWD. Checked voltage at connectors both left and right connectors have no voltage with AWD switch off, and both have 12.4V
      when AWD switch is turned on. Repeated turning switch on and off several times with no change in condition. I am thinking this must be something mechanical with the 
      Hilliard clutch on the right hub ie. weak spring or stuck rollers on the Hilliard clutch assembly (Is this a logical thought?) any ideas on trouble shooting this before I disassemble the 
      right front hub again 
    • sunn
      Right Hand side panel for heat reduction on 2017 Sportsman 570
      By sunn
      Has anyone had experience with the installation of the Optional RH Side Panel Close Off Kit as shown as p/n 2207445 which is supposed to help control the heat on the right side on my legs?  Right now that panel is wide open with excess heat on my leg.
    • DaveswMN
      Hoping against hope that you will tell me that my '86 225 Moto4 is not as bad as I think
      By DaveswMN
      Pulled my '86 Moto4 out of shed where it sat for 20 years. I knew it smoked. checked it over a little put in gas and it fired right up!! 
      Drove about 100 yards, ran about half throttle wouldn't idle.  Put on somenew parts, jug/piston and rings, carb and valve seals.
      'went together ok, tuned it over by hand about 6 revs whick went well. Hit the starter it fired for about 6 revs and quit. tried it again fired once and then th sound of something slipping like maybe chain slipping over spoket.
      Took cover off to watch cam sproket, hit starter again, heard same noise and the cam sproket was not turning but jumping a bit. Chain was still tight. You will probably tell me I need to split the lower case but hoping there mightbe something else.
      I don't fully understand the chain tightener, the plunger only moves about 1/4 inch, should it move much more than that when off the motor and compressing it by hand?
      Thanks for any thoughts.

COMMUNITY SECTIONS

ATV FORUMS

QUADCRAZY MEMBERSHIP

Be a part of best online community of ATV riders and join thousands of people who love ATVs! Share your ATV photos, videos, ATV rides, get help with your ATV and more. Not a member?

SIGN UP TODAY

ADVERTISE WITH US

FOLLOW US ON

  • Automotive Webmaster
×
×
  • Create New...