-
Join Today, It's Simple and FREE!
As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery. Registration is fast and you can even login with social network accounts to sync your profiles and content.
-
Similar Topics
-
By Dra O
posted a while back - it was running at one point - I have all the plastic shroud off - it's down to frame and engine now
-fuel pump: when line from petcock is attached, no fuel comes out other side to carb; the line to the carb is open (can blow through it); I thought when I cranked engine that the pump would spit out fuel on other side but it does not; I removed fuel pump and opened it up - diaphragm looks good - but internal areas had lotsa calcification build up - I cleaned this out and dried it good - the clear plastic pieces (?diaphragms) aren't broken - the spring w/ steel ball on end moves freely; am putting it back on tomorrow; but can anyone answer about the pump? isn't it supposed to pump fuel through it... to other side... to carb? puzzling
-along with fuel pump: I replaced petcock 3 weeks ago (gas tank had rusty fuel in bottom - cleaned it out prior to new petcock); when I turn petcock arrow NOT to on or reserve, fuel comes out of line; when I turn it to on or reserve, fuel doesn't come out; puzzling
-I don't know what's on back of fuel pump - it's a valve that has a hose coming out of it - looks like it goes to engine/carb - I haven't traced this out yet - what is it?
-can squirt gas on air filter and engine will run for 2-3 seconds then stop - fuel in top of carb (under diaphragm) does same
-it likely needs carb rebuild - will get to this - but something isn't allowing fuel to get from fuel pump to carb
-I THINK it has a mikuni model x carb - diaphragm is ID 26mm OD 68mm - hard to find inexpensive diaphragm, I guess because it's a model x
-last thing - I replaced solenoid due to old one clicking; I HAVE to be charging the battery or it won't start/turn over - battery just goes dead; but if charging, it'll turn over nicely; i'm guessing it's a bad battery
-any help appreciated - I've never owned an ATV before - inherited this beast from grandparent in-law
-
By Kawiherder
It starts and runs Ok but after a while the temp gage lights up and the fan fails to start. Any suggestions on where to start looking would be helpful. Thanks
-
By pcumby
Hi guys I'm in the market for a new ATV. I narrowed my choices down to King quad 750 Grizzly 700 and Rubicon 520, I own a 2006 500 Rubicon right now and I like the reliability and power for plowing. However it is not a capable ATV. When quading with other guys it falls short with ride quality and ground clearance. I also have a 500 King Quad 2015 which I like and will keep it for my wife. It is very strong and reliable also. However my plan is to sell my Honda Rubicon and replace it with a 2020 of one of the these mentioned above. Can anyone give me their take on one or all of these machines and why you picked what you picked?
-
By DUBLT
Looking to purchase a windshield for my ATV, suggestions of what to buy with quality in mind and will fit without doing any modifications.
-
By Ted Aregi
I've got a king quad 750cc has anyone converted the fuel pump relay to a stronger fuel pump relay on there king quad?
-
-
-
Similar Tagged Content
-
By Wali
I was riding my 400ex one day and when i shut it off to put it in the garage i tried to start it put again to drive it into the garge and it wouldnt start.I put a compression tester on it and its like 30 psi with out throttle and 0 psi WITH THROTTLE.
when i put my finger over the hole it fell likes its pulling my finger in more then its pushing it out
Has good spark.When i took it into the shop the said it had 1oz of oil in it and a tiny pit of metal shaving(TINY BIT LIKE 30 flakes)
When i try to pull start (push start/roll start) it made a not normal sound and wouldnt stay running.
If my bottom end is blow why would it still turn over fine,
Are my valves siezed or not working properly
or is my timing off causeing valves to not open in correct order with fire
PLEASE HELP all help is appreciated
-
By Coral Breding
I loosened the allen bolts on the carrier and when I went to put my driver in the alot to pull back and tighten the chain, I noticed the holes were facing the front of the bike. I tried to slide a driver in and tighten the chain but the thing would not budge. I nearly ripped the tip off the driver in the slot. Any suggestions?
-
By afa913
Anyone know a place i can find a used stock pipe for a 400ex? I would love to find a take off
-
By Jordan Alexander
The title is for attention. I’m prepping my cylinder head off of an unknown year 400ex to install on my quad. And I’m examining it and there’s literally a Jewish start( Star of David) protruding from the metal on the camshaft side of the head. It’s not imprinted or etched/ engraved. It’s coming out of the metal. DOES ANYONE HAVE INFORMATION ON WHY ITS THERE??? I’ve attached a picture
-
-
Recently Browsing 0 members
No registered users viewing this page.