Quantcast
Jump to content

2000 scrambler 50 no spark

davek

By davek
in Polaris ATV Forum

 Share

Recommended Posts

davek Newbie

davek

Posted
Posted

I have a 2000 scrambler 50 with no spark. It's not the plug or the rip cord.the starter has bin removed. the ignition switch wires have degraded and are falling out. can I jump out the switch and just use a toggle for the on and off, if so how thanks

Dave

DirtDemon Veteran

DirtDemon

Posted
Posted

Sounds like damaged wires are most likely your biggest problem. You can wire in a toggle switch, but I think I would just try to replace the damaged wires with new ones and use the stock switch. If you take the switch apart, you should be able to un-solder the old wires and solder new wires in, you may also want to clean up the contacts in the switch while you have it open.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Popular Now

  • Similar Forum Topics

    • 88bigbear
      1988 big bear 350 no spark
      By 88bigbear
      Bought a 88 big bear 350 4x4 took it for a run and lost spark, found it was stator so I replaced that then took it for a long run and it sat for 2 days and no spark again, this time stator tests good on ohms and voltage for source and pick up coils so I started replacing things including regulator, ignition, ignition coil and plug cap, spark plug and everything tests great including all safety switches until the orange wire for ignition coil from the cdi it only reads 3 volts so I replaced the cdi and still 3 volts, any ideas??
    • cfherrman
      1988 Yamaha 350 Big bear No spark
      By cfherrman
      Fixing for a friend. Atv was at a different friends house to be fixed and he rebuilt the carb and had it running nice, then it shut off and no more. He replaced the key and the coil.
       
      So he got busy, so I am helping, I checked the wiring from the stator to the cdi, and from the cdi to the coil. All is good. I checked resistance on the pickup coil, good, and on the source coil, open. I buy a new stator (China) and the 4 prong plug only has 3 wires in it while mine has all 4. I checked resistance in the source coil and it's in the 300's. I pulled one of the old pickup wires out of the old stator and wire it in the new one. Still no spark.
       
      Why do the wires differ, I checked the VIN again and it's "J" for the year and I got a 1988 stator. Please help!
    • LashinWheeler
      2006 Polaris Sawtooth No Spark
      By LashinWheeler
      Hello all, I have a 2006 Polaris Sawtooth with no spark. It has a dead battery but with a jump pack on it, it will still not Spark. Plug is good, Throttle ETC is not closed, Stator pick up coil seems to Ohm out in the correct range, Unsure how to properly check the CDI. And when ignition is on the Neutral and reverse light come on but after cranking just the neutral stays on. 
       
      Any help would be great,
       
      Thanks!
    • logray
      Looking for Quadrunner Flywheel Starter Clutch Gear race diameter
      By logray
      Hi all, 

      I am wondering if any of you have a Clutch Starter gear from a 1988 era quadrunner 250 sitting around that you could get me a precise measurement of the outer diameter of the race the sprag engages onto, for me? I need to machine a damaged race down and install a hardened sleeve and need that measurement (it's on a different gear than the OEM one, so I can't buy and use a OEM gear). 

    • cruteg8
      Bell Crank Orentation 2000 Polaris Scrambler 400 2x4
      By cruteg8
      Does anyone know  the orientation of the bell crank for scrambler 400 2x4 it was not hooked up when I bought quad the way  i put it high goes into reverse and vise versa I flipped it 180 but that put  the shift rod at big angle and it just kinda grinds into gears so dnt think that is right either pretty sure it has to be the exact orientation and the rod adjusted accordingly but I cant seem to find it anyone knows please help 

COMMUNITY SECTIONS

ATV FORUMS

QUADCRAZY MEMBERSHIP

Be a part of best online community of ATV riders and join thousands of people who love ATVs! Share your ATV photos, videos, ATV rides, get help with your ATV and more. Not a member?

SIGN UP TODAY

ADVERTISE WITH US

FOLLOW US ON

  • Automotive Webmaster
×
×
  • Create New...