Quantcast
Jump to content

  • Do you own an ATV? Join our Forum!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

Rock

2001 Arctic Cat 250 Timing Specs

Recommended Posts

I have an arctic cat 250 atv and I need to know the timing specs and procedures for this engine if anyone can help. Thanks Rock

Share this post


Link to post
Share on other sites


Search the Arctic Cat forum archives, there is a thread for service manuals there.

Share this post


Link to post
Share on other sites


Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Topics

    • By David Miller
      Does anyone know how to access the check engine codes on a 2018 450 sportsman. Just changed battery and spark plug . It runs fine but the light is on and I need this to plow snow and need it reliable. Any ideas . Thanks
    • By Dra O
      Looked at this one-owner 1998  454 today.  Pics below.  Do you see TONS of cash being tossed into this thing?  I like the low miles but I don't like the electrical "arrangement."
      1360 miles - one owner that used it for hunting - owner said it has been outside, as is, for 5-6 years (he originally told me 10 years).
      -a marine battery charges EVERYTHING (I didn't think this was possible) - he did this primarily for the wench  - a charged 12v battery didn't turn anything on the instrument panel - a charged marine battery would help but I didn't have one in my back pocket
      -no oil detected after taking off cap and I put my finger in DEEP.  no gas in tank.  brake fluid reservoir not dried up but has dark/old fluid
      -tires w/ good tread but cracking walls - some rims rusted but appear to be straight           -air box dry but filter old/useless       -original carb - didn't take out to inspect
      -foot shifter felt good/cycled through the gears      -pull start worked but I failed to check for spark
      -and then there's the WIRES... and WIRES... and WIRES.   Basically neuroanatomy 101.  More like Arctic Cat Nightmare 101.  New wiring harness on ebay runs around $70 - but this guarantees nothing.
      But the plastics are good
      Thoughts and opinions welcomed.  "Run away" -- "You're an idiot if you pay more than $XX for that piece" -- "Don't even THINK about it"
      Pictures below - may involve a second/third page
       
       





      more pics





    • By Chris Simpson
      Got a 99 or 2000 bayou 220. Its started making alot of noise, then the starter would spin freely. Took it apart and determined the three bolts in the starter clutch had sheared. Installed the new starter clutch and in the process, not realizing that Japanese motors turn counterclockwise, I turned the crankshaft clockwise about a half revolution so that the key holes would be on top of the crankshaft for easier installation of starter clutch. I get everything back together and try it. The pressure is so great that its very hard to pull with the pull start, the electric starter turns it over but it struggles greatly. A key issue could be this. When I engage the choke the starter will barely turn it over and you can't pull start at all because there's so much pressure. Like the back pressure cant be released once the carburetor is choked. I'm pretty sure by turning the crankshaft clockwise I screwed something up but I cannot figure out what it is. If there's anyone that can give some advice it will be greatly appreciated.
    • By Dwight Williams
      Ok, so I bought a 2006 bayou 250 for 200 bucks, kid couldn't start it and had no idea why it wouldn't run, I pulled the rope and felt what I thought was valve to piston contact, he wanted 500 and I talked him down to 200 and brought it home.  Sure enough, timing was way far out, timing chain incredibly loose.  So for fun I re-tensioned the timing chain and re timed it, got about 120lbs of compression, pretty low.  I cannot get the chain very tight but the the tensioner seems to work fine, the chain guides don't look very worn.  Also, when I took the head off the valves don't look bent and the piston has no discernible marks on it.  Is this an interference engine?  I sure thought I felt some contact with the pull rope but maybe no permanent damage was done?  Anyway, I plan on doing a full top end job as well as timing chain tensioners and hopefully that'll cure it.  Is there any reason other than chain stretch (I measured it and it's ok) or guide wear that would cause the chain to be so loose?  Thanks!
       
    • By Brian Simmons
      I am looking at a 90cc Arctic cat 90cc not sure what year right off hand . The shaft broke off right outside the motor . Can anyone help me ? What do I need to do to fix it ? Do you have any pictures or videos ? Let me know ?
       
  • Similar Tagged Content

    • By Tahj
      I am looking to see why my 2005 Grizzly  660 won't crank. I have set the valves but suspect a loose timing chain.
      When working to remove the valve cover I found a "cap tensioner case" - parts #25  - #299 on Babbitts site.
      The  cover seems to bridge the valve cover and the cylinder head. What the hell is it and what surprises will I  find if I remove it?
      Uncharted territory for me.
    • By Andrew Klein
      Need some help please. I am trying to set timing on 4x4 350 bruin 2006. My brother and I disagree on which ones to use. If anyone has a picture they could share I would greatly appreciate it
    • By Khoranic
      Does anyone know the bolt size that holds the timing chain tensioner on to a 400ex? Thread size and pitch.
    • By YFZ450
      I know how to put it in time, i dont understand the tensioner how it works, i know you have to back it out but should the bike be running when im doin this or can it be shut off.
      Can someone explain the full process of getting the timing chain tight again
  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...