Join Today, It's Simple and FREE!
As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery. Registration is fast and you can even login with social network accounts to sync your profiles and content.
My retaining wall fell 20 feet up my driveway from the entrance. I called my insurance company and was told that there isn’t a lot they can do.
So I called the town to see who built it and the old homeowner did 4 years ago! With no contractor! And the building department passed it for inspection.
There is no geo grid, no drainage, and dirt as a backfill. I bet you I can pull the rest down by hand.
My question is who is responsible? This is not right.
Sent from my iPhone using Tapatalk
I saw this article on Motosport and thought it was pretty good. Anyone add anything?
You might think hopping on-board an ATV and going for a spin is just as easy as taking your regular 4-wheel car for a ride around the block. After all, both have four wheels. How hard could it be?
In many respects, you're right. Some adventure riders choose quads over their two-wheeled counterparts of the dirt because there's less chance of crashing and it's easier to learn. ATVs also offer more manageability for younger riders to get acquainted with outdoor riding than a dirt bike.
However, beginner riders on ATVs tend to make the same mistakes that result in crashes, roll overs and injury that could be avoided with some instruction and know-how. If you're looking at a fun family outing by renting ATVs or want to get into the sport take advantage of the following points and avoid the same mistakes so many other first time ATV riders make that end their day early or before they barely get started.
1. Nerf Bars
Get Nerf bars. These are not soft cushy add-ons that are cousins to the football you use during backyard football games. In many respects, Nerf bars are gigantic foot pegs. Don't bother with traditional foot pegs because you'll constantly slip off and because of the "I feel safe factor" that comes with riding a quad you'll also have a tendency to let your feet drag when riding. That's a recipe for getting one or both of your feet caught in the back tire resulting in serious injury. Nerf bars allow you to stabilize your feet and get maximum control over the ATV
Rest your feet easy on Nerf bars
2. Rolling Over
Believe it or not, it's fairly easy to roll an ATV over. And you don't want to be on the bottom of that sandwich.
The most common way of ending underneath a quad is looping out. That's done by hitting the gas and having little to no experience with the power of an ATV. The front spikes up like an out of control stallion, throws you onto your back like a bucking bronco and then pins you like a UFC Champ.
The second way is when you're having a bit too much fun sliding around in mud or other slick conditions, the tires finally do what they're designed to do and grip the ground but the rest of the bike, with you on it, keeps going.
Finally, those who think they've found their bearings take aim for a steep slope and try to conquer it only to end up upside down or in their attempt to arch alongside said steep hill, tumble over the side.
3. False Sense of Security
This goes somewhat hand-in-hand with the roll over capability that many riders fail to appreciate therefore they also neglect wearing proper protective equipment. Don't think wearing jeans, t-shirt and sneakers is adequate protection when riding a 4-wheeled machine powered by a gas engine that doesn't have seatbelts. You need a helmet, goggles, gloves and riding boots at a minimum. Once you start ripping it on the track or trails add a chest protector, neck brace, knee brace, etc.
4. Throttle Control
Everybody wants to skip the kiddie stage and get right into hair-raising speed when it comes to riding ATVs. OK, most everybody. But for those who do so many put on the cloak of invincibility and think a quad is merely a mini car that finally enables them to release all sorts of pent up childhood inhibitions.
So they jab their thumb into the throttle with the expectation of a controlled roller coaster ride. Instead, they loop out and end up underneath the quad or manage to stay seated only to careen off course and introduce their 4x4 to a large tree. ATVs normally have a thumb throttle and most have an automatic clutch so the clutch is one less thing to worry about. So go slow and figure out how much "thumb" is too much and get used to the speed and power an ATV delivers before really going for a ride. Oh, one more thing, learn to take your thumb off the throttle!
It's not to hard to loop out on an ATV
5. Loading the ATV
Never, ever ride an ATV up a ramp into the back of a pick-up. If you want to know why just go to YouTube. If you want to know how to load an ATV check out this fine piece of quality information on How to Load a Motorcycle, Dirt Bike or ATV into a Truck.
The bottom line to riding an ATV the first time is treat it like you would anything that comes with a modicum of danger. Careless behavior endangers you and others but with common sense and a willingness to learn you'll enjoy of lifetime of riding quads.
For additional information on riding and/or maintaining ATVs see:
10 Quick Safety Tips for ATV Trail Riding Tips for New ATV Owners Choosing the Best ATV for Beginners 10 Things That Alter Your ATV Performance Written By: AndrewT
By Christian Smith
Recently bought a Polaris 425 Xpedition. Main issue is that the quad randomly misfires sometimes. ONLY does it at idle. Everything sounds good. What should I look for? Haven't checked the plug, seems a bit hard to get to, not sure. Headlights flicker at idle as well, is this a sign of a weak stator? Help?
Over the years I have always used a friends machine, and only ride a few times a year. Last week I purchased a 2002 Polaris Sportsman 700. The front diff needs a rebuild, the axles are very loose where they go into diff. My question is, both front wheels rotate forward by hand, but do not rotate the opposite direction. Is this "NORMAL OPERATION" I plan on rebuilding the hubs at the same time as the diff.....
My question about the rear diff, it rolls as if the machine has a total POSI rear axle...……. I lifted the front end off the garage floor with overhead hoist, as I moved it sideways the rear tires skidded rather than rotate. Both would roll forward easy, but not go in a circle. When I drove the machine in the garage making a tight turn I could feel the binding and skidding of rear tires.... Even if the switch was in 4 wheel drive, when it's hanging in te air the ignition is off...….. with the machine in 2 wheel drive mode, is that HONESTLY 1 wheel drive to allow turning without tearing up the lawn? then it locks the rear axle once it's put into 4 wheel drive? I'm guessing the rear diff needs a rebuild also because there is something "BALLED UP" internally locking the rear wheels together?
It's a old machine that was not maintained, I thought the wheels were all rusted, but it was 17 years off baked on red clay. Just wanting to make it a reliable machine. I have great mechanical ability, just lacking a little knowledge of what is suppose to be "NORMAL OPERATING STANDARDS"
Thank you in advance for sharing your knowledge.
Recently Browsing 0 members
No registered users viewing this page.