Quantcast
Jump to content

Recommended Posts

Posted

I bought a 2003 blaster off a friend knowing it needed work at first it wasnt idleing and reving out of control so we figured there was an air leak, we put a new gasket on the base of the cylinder and the head, but now it wont idle and is pouring out blue smoke. Ive messed around with the idle ajustment on the TORS system but it still wont idle, we also found that most of the wires are cut would that have any thing to do with the idle?

Posted

If it is blue smoke then you r burning oil or to much of it. also. your plug could be fouling. is that think oil injection or mixed. i am pretty sure it is a 2 stroke is it not. also if your reeds ar damaged that will cause the same issue. you can change the plug and drain out the tank and put clean fuel in it. if it is oil injection then clean the oil system and reset the mixure rate.

Posted

Its oil injected, so how do i reset the mixture rate? We checked the Crank case and there was no oil so when we put some in i think thats when it happend.

Posted (edited)

If you started getting the smoke after putting oil in the tranny, then you either have a leak in the case center gasket between the tranny and the crankcase, or you have leaky crank seals. Leaky crank bearing seals could also be where you were sucking in air. When you put oil in the tranny, the crankcase started sucking in oil that side instead of air. The crank seals can be changed without splitting the cases, but if the bearings are bad, the case halves need to be separated. Google 2 stroke leak down test. This is an important test to do on 2 stroke engines. For one, the performance of the engine is dependant on alternating pressure/vacuum in the crankcase. Secondly, a leak in the motor will allow the motor to suck in extra air and cause the motor to run lean, this can destroy a motor quickly. The cut wires are probably someones half assed attempt to override the TORS system. You might want to look into a proper TORS elimination kit.

Edited by DirtDemon

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Popular Now

  • Similar Forum Topics

    • By Eisenmatt17803
      Good Morning!
      Has anyone had a problem with the small aluminum 90 degree elbow popping out of the valve cover and blowing oil all over the place? It looks like it is simply pressed in and will most certainly repeat the offense. Any experience you all can share with this issue?
      Thanks in advance.
    • By kevinohio
      My cylinder is full of gas.i thought if carb was messed up.gas came out the overflow.had a cheap china made carburator on it.i ordered a factory used one.couldnt find a new one.also the fuel shut off isn't working right.and going to be needing the battery hold down and seat bracket.where can I get a used one?
    • By Martin82
      Hello to all,
      Im looking for a main wire harness for Polaris sawtooth 200,
       
      Thanks for info 
    • By BillR94
      I suspect this bike may have a bad speed limiter. The part number for is 4060204. I found this one on ebay but it has a part number that is 1 number different. (4060203). It has the same LR44-2 and says its for a 94 Magnum 425. Will this one work on my machine or do I absolutely have to have the 4060204? Your advice would be appreciated. Thank you
      https://www.ebay.com/itm/326817022020?_skw=Polaris+speed+limiter+LR+44-2+4060204&itmmeta=01KF74RJDTYSQNAP11RNJHCRQQ&hash=item4c17d00044:g:IRYAAeSwfO1o7eFo&itmprp=enc%3AAQALAAABAO7PUuNWmJ%2B%2BUShgI9tQz%2Fp%2FPZwHFglDA7v--td9bxBP05QJN8jM6A97tWp7MfGdxP%2Fo9vRaFVpxhV0%2B86jsb4r1WPwXcF%2FLp132KMxBdyLCSwt%2FtSvxD4%2B2RhmZOKzQYHqX0tNsUT1cqqf1TT0TxauZTveHSqgA8UlZ3Qb3ALQlGIIFiaiXjpWNHwRUnyNGKvI5gDVtbwv7eIrkF8m42Bvb75n4dwn0jTJyLPLZveJMPDcjlyHha0wv1Q1JbVnF%2FxxfSi2ros0dbFHRLsBpdH0TT9LNoSTtump3ZDZ%2BA9xqfasfcwHrDJzDX2BDC9Jx8NZeI%2B3mcvOJ7H8qPpwW7OY%3D|tkp%3ABFBMhKfi5Plm
    • By fixitforfree
      I have a 94 Trail Boss 250 2wd that will not go into forward. Reverse works great but forward just clicks but won’t engage. I’ve verified the shift lever is pushing far enough so I believe I have either an engagement “dog” or mating forward gear that are likely bad. I also see a fair amount of metal on the dipstick magnet. But if I ride the machine in reverse the gearbox seems quiet with no other issues by what I hear. That said I’m in process of pulling the gearbox to see what parts I need. The gearbox has 1341124 as the model number as shown in the photo below but I can’t find any gearbox on eBay or the Polaris parts site that matches that number. Is this 94 model a year that used some special gearbox? My tag on the box even looks different than all the tags on gearboxes I see for sale on eBay. I really want to buy new parts for the ones damaged in my gearbox to fix the one I have but just doing research at this point to see what gearbox I have to know which parts I need. Anyone with experience with this I welcome some advice or direction from what you have learned. Just FYI this machine is new to me but cranks, runs and idles perfect. It’s not beat up and will be a gem when I get this tranny fixed. Thanks.

×
×
  • Create New...