Quantcast
Jump to content

  • Join Today, It's Simple and FREE!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

Recommended Posts



Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Topics

    • By Dra O
      posted a while back - it was running at one point - I have all the plastic shroud off - it's down to frame and engine now
      -fuel pump: when line from petcock is attached, no fuel comes out other side to carb; the line to the carb is open (can blow through it); I thought when I cranked engine that the pump would spit out fuel on other side but it does not; I removed fuel pump and opened it up - diaphragm looks good - but internal areas had lotsa calcification build up - I cleaned this out and dried it good - the clear plastic pieces (?diaphragms) aren't broken - the spring w/ steel ball on end moves freely; am putting it back on tomorrow; but can anyone answer about the pump? isn't it supposed to pump fuel through it... to other side... to carb? puzzling
      -along with fuel pump: I replaced petcock 3 weeks ago (gas tank had rusty fuel in bottom - cleaned it out prior to new petcock); when I turn petcock arrow NOT to on or reserve, fuel comes out of line; when I turn it to on or reserve, fuel doesn't come out; puzzling
      -I don't know what's on back of fuel pump - it's a valve that has a hose coming out of it - looks like it goes to engine/carb - I haven't traced this out yet - what is it?
      -can squirt gas on air filter and engine will run for 2-3 seconds then stop - fuel in top of carb (under diaphragm) does same
      -it likely needs carb rebuild - will get to this - but something isn't allowing fuel to get from fuel pump to carb
      -I THINK it has a mikuni model x carb - diaphragm is ID 26mm  OD 68mm - hard to find inexpensive diaphragm, I guess because it's a model x
      -last thing - I replaced solenoid due to old one clicking; I HAVE to be charging the battery or it won't start/turn over - battery just goes dead; but if charging, it'll turn over nicely; i'm guessing it's a bad battery
      -any help appreciated - I've never owned an ATV before - inherited this beast from grandparent in-law
    • By Mike Johnson
      Hello again guys ,. I have a Quadmaster that has a very bad lean to my passenger side wheel. I replaced the a arm bushings with no change in the lean,  I see no bent parts and no adjustments available. It's always been there since I got it but became really noticeable when I put the lift kit on it. I'm going to add a picture of the problem if allowed.

    • By jake Stillman
      Hello I am new to this forum and lt80s I have an 87 that has burned up 3 coil/cdi combos my question is can I out the newer set up on it and if so how do I do it I know they have different number of wires going to the cdi mine only has 2 please help
    • By Quadrunner44
      I have an older 1980s Suzuki quadrunner red lt 4wd (250)
      so just finished putting it all back together and was running fine just needed to adjust the rebuilt carb
      bf decides to hook up an air chuck to the gas tank because it got a shot of air in the gas line well 120psi didn’t agree with any of the parts including the new carb 
      end result : new battery new carb now it just clicks (one single click) won’t turn over 
      hard to pull start gets hung up (unless I remove the spark plug ) gas flooded out the first time but now does nothing purchases a new starter waiting the arrival 
      could there be damage to the crank shaft or pistons etc? Or install the new starter and try to fire it up ? What caused the starter to die after he flooded everything with gas was working fine. 
      Thank you 
    • By bradleyheathhays
      I'm outfitting my middle aged '02 Taurus with a new starter and need some advice on what brand starter to get. I'm tempted to get this reman Motorcraft, the fourth one down in the orange remanufactured section.
       
      CLICK HERE
       
      For $123 that seems reasonable for a OE reman. If not this one I'll probably be going for a reman of another brand so why not go OE?
      The other reman options I'm seeing at the car stores are...
      Napa brand
      Bosch
      Denso
      Driveworks at Advance
      Carquest
      Duralast
      Valucraft
      Ultima
      Bestest
      Should I go with the Motorcraft or one of these? $123 sounds almost too good although I really don't know.
       
  • Similar Tagged Content

    • By Sturgeon
      Really nice and functional bumpers. Fit and finish was great. Go Guru.
       
      l
    • Guest Fox300exchic
      By Guest Fox300exchic
      I was wondering if I could fit a bumper for a different quad on my 300ex? There is one in motosport that I want but they dont make it for mine. If so which one?
    • By arvellaspoon
      When I push down on the rear brake pedal, it makes the left hand brake very sloppy. Is there a way to adjust that? I have a 2007 Suzuki Vinson
    • By chuckcnm
      Hi, just picked up a MOTO 4 YFM255 and want to replace the rear brake pads. How do I get to the back. Guessing I need to remove the brake disk, question any easy way to do this?
      Thanks
    • By Kyboy
      Iam looking for help seperating the rear brake drum and the cover. Any suggestions would be greatly appreciate
  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...