Quantcast
Jump to content

  • Do you own an ATV? Join our Forum!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

dave75

2005 Suzuki Eiger 400 Auto 4x4 - Wont Start

Recommended Posts

I was riding my wheeler the other day shut it off to go in for lunch and when I came back out to start it again all it would do is crank over. Tried a new plug but still nothing. I have power to both wires that go to the coil. I am wondering were i go from here?:confused:

Share this post


Link to post
Share on other sites


could be, i havent tried a new one yet..someone said it might be the cdi box, but holie cow thats spendy..

Share this post


Link to post
Share on other sites


I have an 07 eiger almost same sitUation I turned around in driveway and it died now have no spark just cranks but getting fuel to plug. Did u ever figure out what went wrong with yours?

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Tagged Content

    • By Wali
      I was riding my 400ex one day and when i shut it off to put it in the garage i tried to start it put again to drive it into the garge and it wouldnt start.I put a compression tester on it and its like 30 psi with out throttle and 0 psi WITH THROTTLE.
      when i put my finger over the hole it fell likes its pulling my finger in more then its pushing it out 
       
      Has good spark.When i took it into the shop the said it had 1oz of oil in it and a tiny pit of metal shaving(TINY BIT LIKE 30 flakes)
      When i try to pull start (push start/roll start) it made a not normal sound  and wouldnt stay running.
      If my bottom end is blow why would it still turn over fine,
      Are my valves siezed or not working properly 
      or is my timing off causeing valves to not open in correct order with fire 
      PLEASE HELP all help is appreciated 
    • By Hunter Aldridge
      Some times I get spark some times not can ride then it just dies and wont get spark it has new cdi box and stator but I don't know if it has the pickup coil I'm at a loss
    • By William Sims
      I have a 400 4by4 ,2005 green model,
      wounding how many different CDI boxes will work on it
       
    • By jerry houston
      Eiger 400 Suzuki runs fine Cook-Out joke face off the handlebars put it back on and will not start now will crank no no spark
    • By colin james
      View File 2012-2014 Polaris Sportsman 400 HD Service Manual
      This the factory service manual for the 2012- 2014 sportsman 400 hd service manual 
      Submitter colin james Submitted 02/08/2019 Category Polaris ATV  
  • Similar Topics

    • By ATVNetwork
      news How a recreation staple met its untimely demise.
      FortNine pens a loving tribute to the three-wheeled ATC, and asks: What really killed them? View the full article
    • By NoahJakavi
      Hello i have a linhai 300 of the 2004+- era. I had a cluch problem so we changed it. After changing it has a hard time to start going. When you pop it into gear and press the gas it barely drives but when it starts going about 20km/h it start driving well the acceleration is normal and everything do you have any idea of what could be the problem
    • By ENG243
      Hello 
      I have a 1994 Kawi Bayou 400 which had been running well until it sat for about a month. I left the carb dry while it was park and the temp had dropped below 0C in this time. Pulled it out last night to go for a ride and it fired up just like it should but noticed when I started to head down the road I could hold it to the bar and it didn't seem to accelerate. Lower gears weren't as noticeable but 4th and 5th it just seemed to have no acceleration and half or full throttle  made no difference. if I tried to go into 5th gear with any throttle it would stall. I turned around and just poked home very slow and it seemed to stay running but this was between 15 and 20 km/h max. 
      I have taken the carb apart and it appears to be clean and nothing stood out on inspection to have dirt or ice. Is there something I should dig more into? 
      I have checked the plug and it appears to be sooty with easily rubbed off carbon. I plan to get a new plug today and test. 
      compression with the throttle wide open is 175 psi. 
      I have opened the drain plug in the exhaust thinking there could be a mouse in the exhaust or something but no difference. 
      I do find the engine is tickity compared to my 2000 Honda but I am not sure if this is just me looking for issues or if it has always been this way. 
      If anyone has any insight I would appreciate it.
      In the last 6 months I have done new oil and filter ( mystik synthetic) 
      new Peak RPM CDI 
      I have noticed the fan comes on more often with the new CDI, could this be a program thing?
       
      Mike
    • By VikingTrad3r
      picked up my third timberwolf 250 for my daughters.  these are great light weight little quads.
       
      have a strange one for you.  the quad will NOT start in neutral.  it will start in first. 
      if i lift up on the gear selector just enough to hear the little click (its not loud, sounds like a contact clicking, perhaps the neutral safety switch?) the light will go out, but it won't yet be in first either.  that is how i have shown my daughter to start it and she can.
       
      id like to carry out whatever repair is needed.  i have the pdf of the shop manual but it doesn't really have a flow through diagram.
       
      any help appreciated!  thank you.
      i need to add something.  it feels like i can switch into another gear BELOW neutral.  
      so if i switch to neutral, i can keep pushing the gear selector, and it has another click below the neutral.  the light stays on, and when i pull up into first it kind of feels like it has two positions it moves through to arrive at first.
    • By texaskaw
      fighting this thing for a month now.No spark at plug.
      New ignition coil,pick up coil,stator,reg/rectifier,all new wiring.Started it up today rode for an hour shut it off.Tried to start later wont start.pulled plug wire it firing a blue spark while starter button is pressed.Tried new plug no change. It stared a couple times an ran for few seconds then died.Will CDI act this way? The reg/rectifier get pretty hot is this normal?
  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...