Quantcast
Jump to content

  • Do you own an ATV? Join our Forum!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

Recommended Posts

i noticed today while my son was riding when he lets off the gas smokes comes out the muffler it does not smell like oil but almost like a paper bruning smell it only has like maybe 5 hours one it what could that smoke be from it does when he running and has the gas down and the lets off

Share this post


Link to post
Share on other sites


Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Tagged Content

    • By Austin Rowedder
      Hi I have a 2007 Polaris outlaw 525 irs and am trying to replace the needle bearings in the rear a arms. I was wondering how you go about getting the rubber seal and bearing out!?
    • By stinky
      I have an Outlaw 110 that will struggle to turn the engine over. Jump starting doesn't help other than the battery will drain LONG before the bike eventually starts, so is required. If you keep messing with it long enough it will eventually magically begin to crank fine and sometimes finally start. Once we finally get the bike to start and warm it up thoroughly, it will turn over and start just fine the rest of the day like nothing ever happened... next day it won't turn over again.  Internet research has found lots of people saying they replaced starters, starter clutch, wiring, etc. but with only about 50/50 success rate for their particular problems... and I never found anybody describing a problem like mine, so I'm looking for advice/experience. Would rather not just start blindly throwing parts at it. Does anybody have any thoughts/ideas?
    • By Dravkracing
      Is there anything I can do to make this little quad go faster? Thank you 
    • By Ponetay
      I’m am trying to figure out how to set this to tdc so I can set the valves. Anyone know the procedure?
    • By Xyla Cat
      View File 2006 - 2007 Polaris Outlaw 500 Service Manual
      2006 - 2007 Polaris Outlaw 500 Service Manual.pdf
      Submitter Xyla Cat Submitted 08/25/2018 Category Polaris ATV  
  • Similar Topics

    • By KX420Guy
      Hey guys, Im new here but I recently Picked up a '99 Foreman 400 that apparently just had a top end rebuild. It blows white smoke like crazy and ticks/knocks and seems to follow the rpm's. I haven't done to much trouble shooting yet, It starts and runs like a champ and has good compression. I was just wondering if anyone has any suggestions as to where to go.
      Oh ya the top end rebuild the guy did was according to him he honed the cylinder and replaced the piston and rings, my fear is an ovaled cylinder?
    • By JacobSlabach
      i know this isnt an atv but same type of thing.  I have a riding mower im fixing and selling for my aunt and it has a dead battery.  i jumped it off my atv and when i turn the key nothing at all happens.  i tried jumping the relay still nothing.  this is with the seat down.  you wouldnt think this mower would have issues as its a top-of-the-line brand and almost brand new (aunt found it for a good price, still got tits on tires, just sat for a couple months in a mechanic shop
    • By Chrism
      Hi all, new to this forum so thanks in advance for the help.

      I have recently brought a 2013 power steering fuel injected foreman 500.

      It has a crack in the front casing and was running rough. I have since replaced the front engine casing and this has made no difference to the engine performance.

      It starts and idles but bogs down and starts to die once throttle is applied.

      It maybe be but it also sounds very load.

      I have uploaded a video link of it.
       
       
       
    • By Airborne
      Just got home from voting, this is about the most i will talk politics lol....for the fact that im hoping America gets back to the way things used to be , just my opinion but America seems so much more angrier, im burned out 2020 has been very political and im ready to move forward , im 54 been voting since 18 and have never seen an election like this ...okay Enough ! Lol 
      Dump the masks ,and lets focus on America moving forward ...ugh lets grab a cold Beer and laugh again ......just my 2 cents 🇺🇸😊
    • By Airborne
      Well here we go ... snowing like crazy front lawn covered already lol i guess winter is here , time to set plow up. 
      Last weekend i built a concrete ramp for bringing machines into basement , glad i got that done lol. Wouldnt be doing this weekend. 
      Be safe guysm
  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...