Quantcast
Jump to content

  • Do you own an ATV, UTV or SxS? Join our Community Forum!

    QUADCRAZY ATV Community and Forum are FREE to join! We keep our ATV, UTV, and SxS forums clean and user friendly. All first time posters in our forums will have to wait to have their content reviewed and approved. Once your first ten posts are approved, you will no longer need to go through a forum post approval process. To bypass the approval process with immediate access and a NO ADS experience in our ATV, SxS, and UTV forums, consider subsribing to a Premium Membership

96 kingQuad 300 wouldnt start


Mike8623

Recommended Posts

Questions for you guys, I have a 1996 king quad 300 with less than 2000 miles on it. I started having problems with it starting. had the valves adjusted and it worked for awhile and then started having probllems starting again, had valves adjusted and again it worked for awhile and then it wouldnt start and it seemed each time I had the valves adjusted it was taking less time for it to quit running. I took it in last time for repair and they replaced the whole top end, piston etc. and now it runs pretty well, but I have noticed if I run it 40-50 miles it is hard to start.

Any ideas

Link to comment
Share on other sites

Forgot to tell you folks that everytime the valves were adjusted they were tight. Once they were re-adjusted it would run fine for awhile and then it wouldnt start again. Adjust the valves and it would run again. The last time I run it I put about 50 miles on it and had a hard time getting it started once I turned it off (and that is after it was repaired with a new piston, rebore on the cylinder and rings and gasket at $854.00.

Link to comment
Share on other sites

  • 1 month later...

Im having the exact same problem with a quadrunner 250. The vavles keep tightening them selves out of adjustment..Best I can figure is its a cam or chain problem but not sure which one..If you do figure this out please let me know what your cause was maybe itll be the same for me..Mine started out the same way but now itll only drive for 10 minutes until the vavles get too tight and it wont run any more, it really sucks..Hope u get ur answer.

Link to comment
Share on other sites

  • 1 year later...

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Forum Topics

    • By McG75
      Hello I’m new here and was wondering is anyone knew of good replacement part numbers for front struts and rear shocks for this atv? I think I’ve found a new rear shock, that looks like the original but there is no dimensions or anything and was wondering if there are any afterMarket new front struts available. I know it’s a long shot but any help would be appreciated. 
    • By Its-always-something
      Have a 1998 AC 300 2x4, Just installed a new carburetor. Engine starts easy but the choke RPMs are very hi and take along time (5-10 mins when cold out). After engine has warmed up choke releases and it idles and runs fine., It does no have an electric choke. The choke lever is never used and it seems like an auto choke? Long story short, how can I lower the choke rpm levels?
       
      Also, carb came with a spare145 jet, not 100% sure what is installed. Could this impact choke RPMs?
       
       
      Any help and information greatly appreciated.
    • By Suzukiquad
      Hi, I have been around everything with a motor since I was little, and finally purchased more to get my husband, and kids involved. I have 4 quads I will be searching around for information on. I have two 2002 Suzuki LT80K quads, a 1997 Yamaha Timberwolf 250, and a 1996 Kawasaki Bayou 220. I have had different ones throughout the years, and plan on buying another Yamaha Banshee. I plan on trying to learn more about all of them, so I can customize some of them. I know nothing about them besides how to race them, my dad always took care of the rest, but figured it was time for me to learn. 
    • By kiriyaaoi
      Hello everyone, I just picked up an 02 LT-F250F the other day and have been in the process of tearing it down to fix some stuff- one of which was the cylinder base gasket leaking like a sieve. Well, I know why that is now, and I also discovered that someone had been in there before. I didn't take pictures, but it looks like it was probably run low on oil at some point, the cam journals and the "bearings" (for lack of a better term) in the head and the valve cover are totally wiped out, very deep grooves.  From what I know it's very difficult to repair aluminum in this way, so I'm trying to figure out where to go next.
       
      1. Have someone grind down the head and valve cover and fit actual bearings in since the aluminum is screwed, and have the cam ground down to match.  I have no idea what this would cost.
      2. Buy a replacement head+cam+valve cover.
       
      #1 I was hoping someone might have some advice on, but #2 seems like it'll (probably) be the more cost effective option.  However I'm running into some difficulty, it seems like the 2001 and 2002 models specifically use a different head part number,  11100-19B10, instead of  11100-19B01 like for all earlier models.  What exactly is the difference between them? There are obviously far more of the earlier heads because it ran for over 10 years.  Are they actually interchangeable? I've also noticed there are heads from the LT250EF that has 4 valve heads but also otherwise look identical.  Would those work as well possibly?  I'd like to not have to drop $500 on machine work or new heads on a $1300 quad that I'm already putting a bunch of new parts on.  Oh, and it has a new piston and the cylinder itself looks pretty good too, as I said someone was in here before me.
       
      Any help or advice would be greatly appreciated. I'll post pics of the carnage tomorrow.
         
       
    • By bco20
      does anyone have an owners manual or repair manual i could download ?i got a 2018 king quad 5oo eps special edition can not find either anywhere thanks
  • Similar Tagged Forum Content

  • Recently Browsing   0 members

    • No registered users viewing this page.
×
×
  • Create New...