Quantcast
Jump to content

Recommended Posts

Posted

Changed oil, removed and cleaned float, needle and seat, and carb, changed oil again, still, several gallons of gas seep I to crank case, any ideas please? Not very good at setting the float so I dread rebuilding the carb.

Posted

if you hold the carb upside down and level with the bowl off, measure the distance from the mating surface of the bowl to the top of the float, i think if you are at a half inch or less you should be good. there is a metal tab where the needle slides onto to the float to adjust if need be ...

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.



  • Similar Forum Topics

    • By mehim
      Hi everyone and thanks for reading. 
      My husband and me are getting ready to host the 2nd Quad Runners event at our nudist campground. The first one (last year) went pretty well with about 20 quads attending and have to say, it was a smaller group, but they made up for their size with the large interest in partying and there was plenty of nudity as the Saturday night went on. 
      We have decided to host another one this summer, but we are looking for some fun (but safe) riding events. Our grounds are almost all flat and remember we are a nudist campground so many of us are bare as* naked so "slow ride" events would be the best. 
      Give us your thoughts and ideas and feel free to ask us anything you would like, and we will answer right here in the thread. 
      Thanks for your help and ride safe. 
      BTW, let us know what "anything goes" means for this thread section. 

    • By cruteg8
      Does anyone know  the orientation of the bell crank for scrambler 400 2x4 it was not hooked up when I bought quad the way  i put it high goes into reverse and vise versa I flipped it 180 but that put  the shift rod at big angle and it just kinda grinds into gears so dnt think that is right either pretty sure it has to be the exact orientation and the rod adjusted accordingly but I cant seem to find it anyone knows please help 
    • By toe420
      I got a couple yamaha moto 4 225cc quads. The guy gave me several old starters with them. I see kits are available to rebuild them but does anyone have tips or tricks for doing it? I haven't rebuild a starter before so im not sure what to look out for. 
    • By tflack500tbx
      Background,
      This winter (Dec.) I was plowing and everything just died, just quit.  No lights, no pull start, No nothing.  I've had this problem before and I changed the voltage reg and it ran fine for over a year. Then this.  So I changed it again, thinking this was the same problem.  Tried to start it and a small pin hole in the CDI appeared with electrical smoke.  
      Months go by and I finally decide to just replace parts (I'm Horrible at electrical issues).  I changed the stator, new CDI, new Voltage reg, new starter solenoid, tested the starter (prefect), charged the battery.  
      Went to start it and the solenoid rapidly clicked.  All the dash lights on, headlights work.  Pull stared it and it fired right up no issues.  Looked into the rapidly clicking starter solenoid and it was not enough juice in the battery.  Took the battery completely out and hooked up a jump box to it turned the key, light on, everything looks good.  Pushed the starter button and it fired right up ran great.  Turned it off to test it again, Turned the key and nothing.  No dash lights nothing.  Took the jump box off and pulled started it.  Started it right up.  Re-hooked the jump box, still nothing.
      Any Ideas? 
    • By cruteg8
      Does anyone know forsure if u can swap out the Crank Case on a 2001 kawasaki Lakota 300 sport  with a kawasaki Bayou 300 Im seeing yes and no all over some say the mounting position is different so you can't swap the cases but everyother inernal engine part you can swap then im seeing no problem bolts right on can someone plz clarify who knows forsure 
×
×
  • Create New...