Quantcast
Jump to content

  • Do you own an ATV? Join our Forum!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

auburnfan327

2007 Honda Recon - Tire Size

Recommended Posts

I have a 2007 Honda Recon ES and need some new tires. The stock tire sizes are 22x10-9 and 22x7-11. I'm looking at some Carlisle AT489 tires but the closest sizes i can find are 22x10-10 and 22x7-12. Will they fit? Thanks.

Share this post


Link to post
Share on other sites


No ... the first # is the tire height, second # is the tire width and third # is the rim size ...

you can go a little bigger on the first 2 #s but you have to stay with the rim size (third #)

Share this post


Link to post
Share on other sites
I have a 2007 Honda Recon ES and need some new tires. The stock tire sizes are 22x10-9 and 22x7-11. I'm looking at some Carlisle AT489 tires but the closest sizes i can find are 22x10-10 and 22x7-12. Will they fit? Thanks.

The stock size for that is

Front 25x8x12

Rear 25x10x12

Heres a link for it ! 2007 Honda FourTrax Rincon™ Base Reviews, Prices, and Specs

My sport quad runs 22" tires !

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Topics

    • By Trent Finnessey
      So I’m 14 years old right now..... I’m a pretty good rider for my age, I have a 98’ 300ex that I’m tryna sell. I’m thinking of a 400ex or should I skip the 400 and just go to a 450r or something along those lines? 
    • By dook
      I've been riding Suzuki Kingquad 300's for the last 20 years. I have 3 of them. I love the low gearing, low center of gravity, low rider position, low racks shaft drive and smooth ride, but they are getting old and I'm tired of fixing them. Best engineering of any utility quad, IMO, but the execution...build quality is not up to par with Honda, so the price you pay is lots of wrenching.
      I positively despise CVT type belt drives. My neighbor has a couple of old Hondas, Rancher and Rubicon and I admire the reliability of them. He does very little maintenance and they always run and have pulled my Kingquads home for me when they break.
      Is Honda the only company that makes ATV's that don't have CVT? I like the build quality but I don't like the high rider position caused by the vertical cylinder, the cold nature of them, having to warm up for several minutes and the plastic skid plates. I guess all modern ATV's have the same issues, though (correct me if I'm wrong).
      Been checking with the dealers, it seems Honda foot shift models are scarce. I really don't need devices/gadgets to decide which gear I need to be in. So I'm avoiding the DCT models. I must have IRS and EPS because of my age and physical condition though.
      Is it possible to get a Rancher with IRS, EPS and foot shift? The specs I'm reading show the rancher is 2" lower than the Rubicon. I'm assuming that to be seat height. With vertical cylinder design, the more you grow the engine, the higher you push the seat....at least that's my thinking.
      Any comments from the Honda experienced?
    • By Jteam
      Hello from NC ladies and gents. Been lurking here off and on and don't think I have ever posted up.

      I have a 2009 Honda Rubicon. I was having a shifting problem with the Hondamatic. Determined it to be a loose connection on the gray 21 pin connector at the control unit (ECM/PCM). I located a source for the connector and replaced it. This improved the connectors feel greatly, HOWEVER, even though I thought I was careful transferring the wires/pins from the old connector to the new connector, I must have crossed up a couple wires because now the gear position display (switch is new) no longer works. It worked fine before the connector change.

      No matter where I have looked, I cannot find a "pin out" for the ECM connectors. The factory service manual does not show it and I have a connection at a dealer and their service techs don't have the pin out either! I was a Chrysler/Plymouth/ Dodge tech in another life and cant imagine th factory not providing pin out diagrams for diagnostics!

      I am at a loss unless I either replace the harness, OR find someone that can take multiple photos of the wires going into the gray connector so I can compare mine.

      Any help or advice would be appreciated. I will also post up the location I found the connectors if that is allowed, since it seems that they fail with some age.

      connector source:
      Motorcycle Connectors
      We have Vintage and modern Sport-bike Motorcycle Wiring Harness electrical Connectors, These connectors are purchase directly from the manufacturer, And in many cases the OEM Supplier, The terminals and connectors are superior quality. Most are Manufactured in the, Japan, USA or Europe. Bullet... www.cycleterminal.com
    • By Rich1028
      2008 Honda 400 Ex and a 2014 Honda 400 X
      We Just Picked up two Quads Friday,and we took them out riding,great machines!
       

  • Similar Tagged Content

    • By Aj Hurtibise
      I have a 2000 Honda trx90 I got from a buddy for free he said it needed a carb so I put his old carb back on it to try to get something out of it and it does not have any Spark. I already replaced the ignition coil I don't know much about four wheelers but I am a technician so I do know my way around a motor any electrical help would be wonderful or specs I don't have the best digital multimeter either.
    • By Aj Hurtibise
      Hey guys I'm new to the Forum I just got a 2000 Honda trx90 looking to make it go a little bit quicker I don't know much about four wheelers but I am a technician at a dealership so I know my way around a motor.
    • By Admin
      Looking for Honda ATV VIN (Vehicle Identification Number) Number Decoders? Once you find your ATV VIN number off the tag on your Honda ATV, you can go to all kinds of websites that have VIN Decoders available. The best ones are backed by the Honda ATV manufacturer, however there are plenty of aftermarket Honda ATV VIN Decoder websites on the web. This topic will stay pinned and if you find any to add, please do it with a reply. 
      The following Honda ATV VIN Decoder websites are available where you can just enter your VIN number and it will shows you some of your ATV model details:
      CycleVIN https://www.cyclevin.com/
      KBB.com https://www.kbb.com/vehicle-history-report/ 
      CARFAX https://www.carfax.com
      autoDNA https://www.autodna.com
      VinAudit http://www.vinaudit.com/
      decodeTHIS https://www.decodethis.com
      VINCario https://vindecoder.eu/
      NICB Theft Check https://www.nicb.org/theft_and_fraud_awareness/vincheck 
    • By Guythis448
      Looking for help on wiring up stock wiring harness specifically for a '88 Honda TRX 300 
      If anyone could drop a link or send me a PM it would be much appreciated 
    • By Wali
      I was riding my 400ex one day and when i shut it off to put it in the garage i tried to start it put again to drive it into the garge and it wouldnt start.I put a compression tester on it and its like 30 psi with out throttle and 0 psi WITH THROTTLE.
      when i put my finger over the hole it fell likes its pulling my finger in more then its pushing it out 
       
      Has good spark.When i took it into the shop the said it had 1oz of oil in it and a tiny pit of metal shaving(TINY BIT LIKE 30 flakes)
      When i try to pull start (push start/roll start) it made a not normal sound  and wouldnt stay running.
      If my bottom end is blow why would it still turn over fine,
      Are my valves siezed or not working properly 
      or is my timing off causeing valves to not open in correct order with fire 
      PLEASE HELP all help is appreciated 
  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...