Quantcast
Jump to content

2004 Honda Rancher 400 - Grinding In Louisiana

tuddyt

By tuddyt
in Honda ATV Forum

 Share

Recommended Posts

tuddyt Rookie

tuddyt

Posted
Posted

im new here and have a problem bought a 04 honda 400 at and i change the centrfugal clutch,drum and one way bearing now when the engine is cold it grinds,boggs down until the motor warms up then everything works fine. put 20/50 gn4 honda oil in it also appreciate any help thanks

Link to comment
Share on other sites
quadnut20 Grand Master

quadnut20

Posted
Posted
im new here and have a problem bought a 04 honda 400 at and i change the centrfugal clutch,drum and one way bearing now when the engine is cold it grinds,boggs down until the motor warms up then everything works fine. put 20/50 gn4 honda oil in it also appreciate any help thanks

Welcome to QC !!! Get ahold of OX and down load a manual for it ! Might help ! What oil does honda say to put in it ?

Link to comment
Share on other sites
tuddyt Rookie

tuddyt

Posted
  • Author
Posted

im new here wounder if someone could help i have a 04 honda rancher 400 at and i changed my circlutch and drum and bearing now when the motor is cold it grinds,boggs down after the engine warms up everything works fine i did put 20/50 honda gn4 oil. any suggestions

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Forum Topics

    • Mhatayas
      Oil leak 1985 suzuki 250
      By Mhatayas
      What should I do about this , bad oil leak where the filter cover bolts on . Can I use some gasket maker 

    • BruceG
      2005 Bruin 350cc Oil pumping into airbox
      By BruceG
      Hi guys. I have a problem where the quad will start and run well for about 5 minutes and then it dies. On inspection the airbox has oil in it (quite a lot). The oil is pumping through the cylinder head breather hose. This problem first happened suddenly. I have since done the top end including, piston, gaskets, rings and valves. I have also done the carb (not that I thought that this was the problem). The compression seems normal. The only thing that I can think of, is that I did not grind the valves well enough. Anyone experienced this? If so, how did you fix it? Any other thoughts?
    • N00bie
      2012 John Deere Gator 850i RSX Idle Problem
      By N00bie
      From Arkansas. Just bought a 2012 Gator 850i RSX because I could not pass up the price. BUT it has an idle problem. So, to be honest, I joined just to get a service manual. I have a choice: 1)Buy a hard copy: ~$100; 2)Buy a CD ~$35.00; Get a direct download for free posting 10 times; or get a download for $29.00 (subscription). Haven't decided what to do yet.
    • semicolon
      TRX350D fuel pump problem
      By semicolon
      Hi, I am having issues with my TRX350D fuel pump.  It suddenly stopped running so I have replaced all the fuses and cleaned all the terminals.  I have fitted a new pump, fuel cut-off relay and rectifier.  Still nothing!!  The pump runs when attached to a battery.  The engine will start on the choke and the filter fills with fuel but it will  not rev and dies when the choke is closed. I have power to the relay but nothing at the pump black/white wire when cranking the engine.  Any ideas where to go from here would be very much appreciated!!
       
    • skittle021
      Super Weird Problem with Primary Sheave/Clutch... (Hisun 550)
      By skittle021
      So I've got a Hisun 550 that I was doing some work on that required removing the CVT and it's housing. Upon attempting to reinstall the clutch, sheaves, etc, I found that the belt no longer fits - it's far too wide. None of the parts have been replaced, they're all OEM. Exactly the same parts as what I took off a few weeks ago.
      To be more specific, my belt is 1.25in wide, but the gap between the clutch and the primary sheave is only 7/8in wide. I'll include a few photos to explain.
      Has anyone ever experienced such a bizarre problem? Any help at all would be appreciated, I've been stuck on this for a month. I'm open to just about any suggestion.
      Photos: 
       





COMMUNITY SECTIONS

ATV FORUMS

QUADCRAZY MEMBERSHIP

Be a part of best online community of ATV riders and join thousands of people who love ATVs! Share your ATV photos, videos, ATV rides, get help with your ATV and more. Not a member?

SIGN UP TODAY

ADVERTISE WITH US

FOLLOW US ON

  • Automotive Webmaster
×
×
  • Create New...