Join Today, It's Simple and FREE!
As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery. Registration is fast and you can even login with social network accounts to sync your profiles and content.
Well I came on here hoping to read a manual about the quad but found that I have to make some posts before that can happen, so here is one.
I work on peoples stuff. Had this well used unit come to me with a no start issue. I found it had fuel and spark was good but it only had 30 pounds of compression. I put each cylinder to TDC and feed the plug hole with a small amount of air pressure and could hear the escaping air coming out the carb openings. I then checked the valves lash at TDC and found that booth cylinders had 0 lash for the intake valves. I reset the lash to .003 for all the intake valves and reapplied a small amount of air pressure and the leaking of air was gone. I then spent a few hours screwing all the parts I had to take off, back together and then drove it out of the shop.
The lash was only 1/4- 1/2 a turn too tight that caused the valve to stay open just enough to make it not start. IMO the heads could use an overhaul some time soon as the valves and seats have become a bit warn.
These ATV's just have too much crap stuffed into a small space, I wounder how many fasteners are used to hold 1 ATV together?
By Frank Angerano
So here’s a question. I have seen a few members that have recently purchased a used bike. Also a HUGE amount of so called new members who have purchased a used bike and have come here “just here for a manual”.
Some have been disappointed with the bikes and or knew they were getting a broken bike with some mechanical experience thinking hey I can fix it. So here’s my take on buying a used bike. Anyone who has followed some of mine and other members posts about what to look for when buying a used bike here’s a few pointers on what to look for.
1. I always check the oil and look for moisture, metal shavings and color.
2. Feel the compression or take a compression tester with you.
3. Check for spark (if the bikes not running)
4. Take a small jumper pack to verify that the starter cycle works and the bike cranks.
5. Look for bent or cracked frame/welding that was done on the frame from maybe a wreck.
5. Mismatch plastics by looking under neath.
7. Bolts on the engine/frame that look like they are stripped from someone taking the bike apart.
8. Any kind of scilicone or gasket adhesive that was used on a cover plate or engine seem where the engine was taken apart.
9. Patches on the exhaust pipes with sheet metal or jb weld patch material.
10. Wiring messes on the harness like bundles of tape where the harness was opened up and taped up for an after market device or just plain butchered up.
11. Put the bike in gear (running or not) and roll the bike back and forth to see that the gears work and you feel resistance like the engine is trying to spin while pushing it forward as if you were push starting it
12. I keep a vin# decoder website on my phone as a favorite to double check the year of the bike .
All though nothing is fool proof these tips will help you along while buying a used bike. Not only that but it will help you negotiate a fair price for a bike that may have one of the above problems.
I have minimized this entire process down to about 15 mins. I buy all the time so I don’t expect you to do the same or have a compression tester etc but use some of these tips when buying and go into the purchase with confidence!
I would like to hear anyone else that has any input on buying a bike and what to look for!
Hello guys! I ride a triton 450 super moto. i hawe change connecting road... Now all is okey,test drive ok manny km done. But there is one problem...i hawe buy a new accu. But the starter is verry hard rotate...almost stops. So the motor is wery hard to start. I hawe trie connect the starter directley to accu and its the same thing.Before rebuild the starter has work normal.
What hawe i done wrong?
Sorry for my English:)
Similar Tagged Content
I need to know what I have and what tire really go on it, Mine has 24x11x10 on the back and 22x8x10 on the front and I need new tire but I don't think are the right size. Also I can't find the model number listed but it looks like a 250 quadrunner 2wd and I think it is a 1987 maybe, can anyone help me, also I it has a rich running sound and I put a carb diap in it and cleaned the carb. is there a jet needing replaced?
:confused:need a repair manual or help in what to look for thank you Bill
for you muddober to make clear to you the neutral light and the gear light
do not light up win shifting fuses are good Iuse my CAt for hunting im dissable the atv is my leag s thank you
Recently Browsing 0 members
No registered users viewing this page.