Quantcast
Jump to content

Kodiak 400 cold weather problem

BCNemo

By BCNemo
in General Talk - Anything Goes!

 Share

Recommended Posts

BCNemo Newbie

BCNemo

Posted
Posted

I have a 2001 Yamaha Kodiak 400 (YFM400FWAN©) On a recent hunting trip a problem popped up and I hope someone else has experienced this, so that I can learn from them instead of going on my own hunt for an answer.

The Problem:

On cold days (sub 25 degree) I choke the Kodiak and it starts instantly. It revs up and runs on "high idle" without any problem. However when I return the choke lever to its "normal" position the ATV continues to run and a very high idle. I cant put it into gear until the idle comes down, which it doesn't. In order to use the bike I have to shut it off and when I restart it I must place it into gear before the engine gets a chance to rev up. It then returns to a normal idle and the machine behaves normally. This only happens on real cold days but it is a problem I want to fix. Can anyone offer some help?

  • 7 years later...
Gwbarm Grand Master

Gwbarm

Posted
Posted

Cold air is thicker than hot air, so it takes a little longer for things to work properly. The fix would be to adjust the carb mixture for colder air. I dont think there is a problem it is just factory set for a certain temp range. 

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Forum Topics

    • Kaz
      1999 Yamaha Big Bear 350 4x4 no spark
      By Kaz
      Troubleshooting a no spark issue, was running OK, maybe a little rich, turned it off, now no spark. I've checked/ohmed out the main key switch, the start/stop switch, neutral switch, brake switch - all good. It will crank the starter, but no spark with the starter or when I try the pull start. I've checked all fuses and diodes. Swapped battery. New plug. New coil. Swapped in a used CDI - no help. Traced, removed, cleaned, reattached all grounds. Removed things like my winch from the circuits to be sure a bad relay or something was dragging it down. When testing voltages, the orange wire going from the CDI to the ignition coil shows no/very low voltage-shouldn't it have 12V on it? Sometimes I get a very weak, intermittent glow on my spark tester, but not enough to fire the plug. I've checked continuity on just about all wires in the harness. Checked/cleaned/lubed w dielectric grease- all connections, redid a few that looked old/dirty. I've checked the stator resistances, all good, but have a stator and rectifier ordered anyway, will arrive Sunday. I verified that the rectifier has a voltage output back to charge the battery while cranking - 10.5-11V, low, but expected while starter is engaged. What else can I check as part of troubleshooting? I have a Haines service manual, but the 1999 350 4x4 seems to be an odd model, there isn't an exact electrical diagram for it, but found one for another year that has all the same number of wires and same color wires, so I've referenced that. Any hints, tips or advice would be appreciated! Thanks!
    • Travis_Smith
      KVF 400 Float Height
      By Travis_Smith
      I have a 2002 Kawasaki Prairie KVF 400 and im trying to figure out the actual float height... i have read 17mm +- 2mm, seen 13mm and 23mm... what is happening is it will start right up, rev a little and all is fine, when it warms and you put a load on it bogs down and sputters. no i don't have a manual
    • fwsamm
      2001 Yamaha Bear Tracker Circuit Relay Issue
      By fwsamm
      Im aware that this relay needs a positive (+) and a negative (-) to activate the other side. The blue wire is the neutral wire so when in neutral it gets ground. The green wire is from the parking break; when you pull the break in it gets ground (-). however one of those two needs to be neutral so that the positive from kill switch can go to the starter relay. The ground from the starter relay is from the start switch. Which one (neutral or parking break) should have a positive (+) voltage?
    • KSIM
      CFMOTO C-Force 400 Service Manual
      By KSIM
      View File CFMOTO C-Force 400 service manual
      C-Force 400
      Submitter KSIM Submitted 03/19/2025 Category CFMOTO ATV  
    • Kawasakibayounospark
      Kawasaki bayou 400 no spark
      By Kawasakibayounospark
      any one know much about how this system works. Replaced voltage regulator cid box coil pickup coil have power to cid box none out to coil any thoughts. This is cid box number three 

COMMUNITY SECTIONS

ATV FORUMS

QUADCRAZY MEMBERSHIP

Be a part of best online community of ATV riders and join thousands of people who love ATVs! Share your ATV photos, videos, ATV rides, get help with your ATV and more. Not a member?

SIGN UP TODAY

ADVERTISE WITH US

FOLLOW US ON

  • Automotive Webmaster
×
×
  • Create New...