Quantcast
Jump to content

Recommended Posts

Posted

I've got some good parts left over from my recent 4wd 2003 Big Bear adventure. Used on 2000-2010 Big Bears.
Very good complete head-fits 350 also, came off 400  2002, Have timing chain, gear,  guides, case & trans (2wd)
Fuel tank, harness, misc. electronics, front shocks/springs, also have some other stuff.
Most parts also fit some 90's models, (Kodiak 400 '93-'98), check it to verify. 
Located near Chattanooga, LMK what you need, offer, cash/trade.

  • Like 1
  • 1 month later...
  • 3 weeks later...
Posted

HI there do you have a rear axle or rear arm supports? I have a 2005 Big Bear 400 that was rolled and hit the rear right tire good. Bent rim and snapped rear arm support component

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.



  • Similar Forum Topics

    • By logray
      Hi all, 

      I am wondering if any of you have a Clutch Starter gear from a 1988 era quadrunner 250 sitting around that you could get me a precise measurement of the outer diameter of the race the sprag engages onto, for me? I need to machine a damaged race down and install a hardened sleeve and need that measurement (it's on a different gear than the OEM one, so I can't buy and use a OEM gear). 

    • By Dsluder
      I am having an issue with a hs500. I bought it broken and have been trying to get it running. It seems to be starving for fuel. If I put my hand over the intake it will crank but will not run for very long because I'm not able to get the correct airflow with my hand. The things I have done so far are. Replaced the fuel pump, fuel filter, mass airflow sensor, idle air adjuster, fuel injector, cleaned the throttle body, replaced the ecu, and still the same issue. I notice the injector does not spray when removed from the head. I dont know if that is common. 
       
      I am out of ideas on what to do next. I have removed the fuel line from the injector and it is getting plenty of fuel. If anyone has an idea on what could possibly be the issue I would be happy to try anything at this point.
    • By Yamahahahaha
      I'm in the middle of repairing damage from the chain coming off of this from the previous owner. (I learned this is somewhat common on these for various reasons.)
      What are you guys using to either help keep the chain correct and on the sprocket or guarding your engine in the case that it comes off / breaks?
      Is there an upgraded guard that can bolt around the sprocket in replacement of the currently broken OEM alluminum?

    • By buriedpast
      As the title says, I've got a crankcase full of fuel / oil to deal with and figure I'll just start from the top and move through the system.  Going to start with a rebuild of the petcock and then the carb if the problem isn't fixed with the petcock rebuild.  I figure I'll go with a Moose kit unless others with experience recommend another brand (All Balls, etc.)
      Any suggestions?  Thanks in advance.
    • By HHurks
      Yesterday I got a UForce 1000 as my first bike and I am wondering if there are any owners that could advise where I can find budget parts and accessories for it.
      I tried looking StarknightMT, but the filtering is a bit unreliable, so direct links or exact names are much appreciated.
      I'm mostly interested in sliders and side cases, but any advices for "must haves" are welcomed.
      Thank you!
×
×
  • Create New...