Join Today, It's Simple and FREE!
As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery. Registration is fast and you can even login with social network accounts to sync your profiles and content.
By Flipper Tiffany Roper Jones
All I have been through everything. Bought brand new.
Throttle safety switch
Cam and rockers
Fuel safety switch
Everything every forum has spoken of I've bought sealed airbox completely tight unplugged black wire on trans. I have literally done everything in the book.Checked oil today full of gas anyone no anything what might b wrong. Next I'm taking head off and making sure valves seat any ideas.
I am in need of a manual for my KLF 300 Bayou 4x2 . I've found others on here for the 4x4 model, but was wondering if I need a separate 4x2 manual. Does anyone know?
View File 2018-19 Polaris Ranger 900-1000 XP Crew Service Manual
2018-19 Polaris Ranger 900-1000 XP Crew Service Manual - Full service manual
Submitter flyinbrian365 Submitted 09/19/2019 Category Polaris UTV
Similar Tagged Content
By Ryann Racho
So Id say about 2 years back I bought a 2013 Polaris Sportsman 500 H.O. off of my uncle. It ran perfectly, nothing wrong at all. I usually go mudding with it or just ride trails with buddies. So as you would assume, the quad is quite dirty from sitting for a few weeks.
STUTTERING PROBLEM: I noticed one day out of nowhere that in high gear at 15-20 MPH, I was already maxed out at 4500-5000 RPM It would get to 15-20 mph, max out on rpms and start sputtering. It sounded like it was basically acting like it couldn’t go any faster than this.
IDLING PROBLEM: I was fucking with the carberator the other day maybe thinking that is causing my sputtering, and now my idle will shoot up to 2600 on start usually, then I will turn the throttle adjustment down to the normal 1400. The rpms with then fluctuate 10-30 rpms back and forth repeatedly, it will then run for about another 30-60 seconds and the RPMs will slowly drop to about 900-1000 RPM and stall out. I replaced the carburetor and everything seems to be working perfect on that, no leaks and what not but it’s still acting strange. Also, I’ve noticed that when looking into the Electronic Throttle Control that two plates that aren’t supposed to touch have to be WAY past touching to even try to fire up. Even when set at a wide open throttle like that, I still have to give it some throttle to get it to fire up.
Here is what I have done so far:
Checked the belt and clutch
Changed out spark plug (Last one was covered in carbon)
Cleaned the intake and air box
Replaced the carburetor
Replaced the inline fuel filter
Checked that all lines on carburetor are connected into the right spots
Checked If intake boot was cracked (Not from what I can see)
Unhooked and reattached new carburetor (About 4-5 times)
Cleaned battery terminals and battery off
Shut on and off Gas Line Cutoff Valve
My next thoughts are that maybe the TPS is fucked up or maybe the Spark Arrestor is plugged with mud. I was thinking tomorrow to purge the exhaust and also check the ohms output on the TPS.
ANY HELP IS GREATLY APPRECIATED. I HAVE BEEN BATTLING THIS FOR WEEK AND REALLY WANT TO GO RIDING. THANK YOU!
Over the years I have always used a friends machine, and only ride a few times a year. Last week I purchased a 2002 Polaris Sportsman 700. The front diff needs a rebuild, the axles are very loose where they go into diff. My question is, both front wheels rotate forward by hand, but do not rotate the opposite direction. Is this "NORMAL OPERATION" I plan on rebuilding the hubs at the same time as the diff.....
My question about the rear diff, it rolls as if the machine has a total POSI rear axle...……. I lifted the front end off the garage floor with overhead hoist, as I moved it sideways the rear tires skidded rather than rotate. Both would roll forward easy, but not go in a circle. When I drove the machine in the garage making a tight turn I could feel the binding and skidding of rear tires.... Even if the switch was in 4 wheel drive, when it's hanging in te air the ignition is off...….. with the machine in 2 wheel drive mode, is that HONESTLY 1 wheel drive to allow turning without tearing up the lawn? then it locks the rear axle once it's put into 4 wheel drive? I'm guessing the rear diff needs a rebuild also because there is something "BALLED UP" internally locking the rear wheels together?
It's a old machine that was not maintained, I thought the wheels were all rusted, but it was 17 years off baked on red clay. Just wanting to make it a reliable machine. I have great mechanical ability, just lacking a little knowledge of what is suppose to be "NORMAL OPERATING STANDARDS"
Thank you in advance for sharing your knowledge.
By colin james
View File 2002-03 Polaris Sportsman 600/700 Service Manual
This is the service manual for the 2002-03 Polaris Sportsman 600/700 ATV, download all the chapters for the complete manual.
Submitter colin james Submitted 01/02/2019 Category Polaris ATV
Recently Browsing 0 members
No registered users viewing this page.