Quantcast
Jump to content

  • Join Today, It's Simple and FREE!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

afa913

Need used stock pipe for a Honda 400ex

Recommended Posts

Anyone know a place i can find a used stock pipe for a 400ex?  I would love to find a take off

Share this post


Link to post
Share on other sites


Look on eBay.  It will be a used pipe but most likely in good shape.  I’ve picked up a few used exhaust pipes, silencers etc. factory parts that bolted right up.  Just make sure of the year and keyword used.  

  • Like 1

Share this post


Link to post
Share on other sites

I would agree with @Frank Angerano, look on ebay for used.

I changed your topic title to be more descriptive of what you are looking for on your Honda 400ex.

  • Like 1

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Similar Forum Topics

  • Similar Tagged Content

    • By afa913
      Am i better off to just replace the bearings or buy the whole carrier?
    • By Jordan Alexander
      The title is for attention. I’m prepping my cylinder head off of an unknown year 400ex to install on my quad. And I’m examining it and there’s literally a Jewish start( Star of David) protruding from the metal on the camshaft side of the head. It’s not imprinted or etched/ engraved. It’s coming out of the metal. DOES ANYONE HAVE INFORMATION ON WHY ITS THERE??? I’ve attached a picture 

    • By 400ex
      So after my 400ex pep up (High comp piston, stage 2 hot cam, and some others), There was a malfunction with the rocker arm jam-nut; guess it wasn't torqued to spec. The rocker arm nut caused the lash to become too out of clearance and I bent a valve on a test rip high in the rpm range. There was no damage to the piston but only that valve, a couple dents in the head, and a completely destroyed valve guide. So I decided to take it upon myself (after watching kenoconnors race porting instructions and reading up on this subject) to port my cylinder head significantly. I had the head decked, cylinder honed and smoothed/polished the dome/exhaust port (intake wasn't polished but dimpled slightly to ensure fuel atomization). So after porting, decking the head, I had all valves and guides replaced/reamed, 5 angle valve job, and recut seats, then I installed xr400 gaskets (for higher compression), carb jets; 42 pilot, 175 or 6 main not sure, dynojet needle, k and n filter with no lid, enlarging of header ports and big gun eco slip on exhaust for a 450r, trx 250r coil (adds 1000+ rpm to limiter), 11:1 85mm piston, stg 2 hc with springs and retainers replaced, and polished rocker arms. I then replaced both sprockets one down in front and stock in rear, o ring chain, and 18in tires. There is a larger list of mods but these were the only ones affecting acceleration/performance. On the dyno, this quad put down 42rwhp and was estimated at 46 to the flywheel. Once again this was 42 to the wheel on the stock bore/carb size/header. All this was done at 16 yrs old. You may not be able to see it in the picture but peak whp was 42 on a mustang dyno.


  • Recently Browsing   0 members

    No registered users viewing this page.


×