Quantcast
Jump to content

Recommended Posts

Posted

Hey everyone im new here, i have a problem with my 2001 suzuki quadrunner 500. When i start the bike up it sounds fine but a few seconds later the idle speed just keeps rising to where you cant put it in gear, and if im lucky it will climb down to where i can put it in gear but when i press the gas it immediately want to die. Please help me!

Posted

Check and see the choke, it may be stuck.  Double check that and the cable but look good because sometimes it’s the choke connector inside the carburetor. 

If that’s all clear it’s possible that the carburetor needs an adjustment. But you have to figure out why because if it was running good and just started acting up then you have to find out what.  So  if the bike was fine before then something changed that.  Maybe a piece of debris/dirt got into the carburetor somehow, maybe form dirt inside the tank, bad gas who knows. 

Also look at the air intake and make sure filters are all good and nothing got sucked into the carburetor like a piece of the air filter if it was crumbling. 

I would start there. 

Posted

It did this when i got it but the starter went bad and had to wait for it to come in the mail, i got the bike a week and a half ago. I will check the choke and filter tomorrow, thank you very much

  • Like 1
Posted

Check  also  for a weak return  spring on the  main  jet needle diaphragm allowing the  carb to  creep  open  above idle ,  and make sure there is no air leak between the  cab and intake . There could be a partially  plugged  jet making the  carb run  lean. That will  make it rev  high at  idle  and die  when you open the throttle . Before digging deeper ,  check the idle air  adjustment.  Most  carbs  are set from about  3/4  to  1  1/2  turns out from gently  seated. Try turning yours in or  out about a 1/4  turn  at a time to  find the best  spot   for idle and no stall. It sounds like it is  burning  lean right now

  • Like 1
  • 3 weeks later...

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Popular Now

  • Similar Forum Topics

    • By Yamahahahaha
      I'm in the middle of repairing damage from the chain coming off of this from the previous owner. (I learned this is somewhat common on these for various reasons.)
      What are you guys using to either help keep the chain correct and on the sprocket or guarding your engine in the case that it comes off / breaks?
      Is there an upgraded guard that can bolt around the sprocket in replacement of the currently broken OEM alluminum?

    • By kevinohio
      Does anyone have a copie of the owners/operators manual.the basic book that comes with the atv.i need the smaller one.i have the great big repair manual one.
    • By buriedpast
      As the title says, I've got a crankcase full of fuel / oil to deal with and figure I'll just start from the top and move through the system.  Going to start with a rebuild of the petcock and then the carb if the problem isn't fixed with the petcock rebuild.  I figure I'll go with a Moose kit unless others with experience recommend another brand (All Balls, etc.)
      Any suggestions?  Thanks in advance.
    • By rjsummer
      Just picked up an 84 LT185 ATV, I understand there was an accessory add  on that gave it electric start, anyone have any info about that kit? 
    • By Rockbottom
      2008 400 big bear was running now will not start
      have power to relay, in neutral, press start have power to starter but nothing happens starter does not turn
      i have good ground at battery to frame and added ground from wire harness to frame beside batter/ frame ground
      blue white wire to cdi has power with key on
      I believe the neutral lock out is working since is was before i shut it down
      if i put  it in gear and hit the start button with key on the relay does not click or send power the starter
      The 3 wires at the relay have power with key on
      What should i test next?
      thanks ahead
×
×
  • Create New...