Quantcast
Jump to content

Recommended Posts

Posted

I replaced the main , pilot and starter jets and it will not start , it wants to try and start , this is a fuel issue I think , what part of the carburetor might be plugged up if it will not start , any ideas

 

2008 Honda TRX450R

Posted

You have to take the carburetor off of the bike and completely tear it down. You will need a small piece of wire to clean every small port on the carburetor as well as a small can of air to blow out the carburetor ports while your cleaning it.   The part of the carburetor that’s probably jammed up is the float and fill needle inside the bowl. Not allowing fuel to get into the engine. Make sure you work on a clean surface and blow every small oraface out of the carburetor.  

There is also a fuel air mixture screw on the carburetor before you take that out it would be best to count how many turns it is set at from a snug tight position so you put it right back where it was or close to it when your done.  

  • Like 2
  • 2 months later...

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Popular Now

  • Similar Forum Topics

    • By Joeguy
      After i did my rebuild it seems to not want to shift well. I think the cable is alright, and when it does shift its nice and solid. I have to basically use my hand to shift and i have to pull or push it very far, like max travel, to get it to shift. I also tried adjusting the clutch set screw. Any ideas where to go next, or maybe i should just grab a new cable to try.
    • By realpilot
      I am unable to find a wiring diagram for this UTV.  When I turn the switch to on, the contractor does not engage.  The Brake pressure switch and the parking brake switches work correctly. What else should I be looking for?  All of the diagrams I have found are for newer models and the wire color coding is different.
       
      Thanks
    • By Cj Winds
      I have a 2009 Honda Rancher TRX420FA with shifting problems.
      Usually it shifts ok when cold but after couple minutes it will stop shifting with no codes.
      The 1st shift clutch oil pressure when in first gear is 74psi. The 2nd shift clutch oil pressure when in second gear is 74psi.
      The 1st shift clutch oil pressure when in neutral is zero. The problem is when the tranny is in neutral the 2nd shift clutch pressure starts around 10-15psi and builds to 20psi. Is this normal?
    • By mehim
      Hi everyone and thanks for reading. 
      My husband and me are getting ready to host the 2nd Quad Runners event at our nudist campground. The first one (last year) went pretty well with about 20 quads attending and have to say, it was a smaller group, but they made up for their size with the large interest in partying and there was plenty of nudity as the Saturday night went on. 
      We have decided to host another one this summer, but we are looking for some fun (but safe) riding events. Our grounds are almost all flat and remember we are a nudist campground so many of us are bare as* naked so "slow ride" events would be the best. 
      Give us your thoughts and ideas and feel free to ask us anything you would like, and we will answer right here in the thread. 
      Thanks for your help and ride safe. 
      BTW, let us know what "anything goes" means for this thread section. 

    • By logray
      Hi all, 

      I am wondering if any of you have a Clutch Starter gear from a 1988 era quadrunner 250 sitting around that you could get me a precise measurement of the outer diameter of the race the sprag engages onto, for me? I need to machine a damaged race down and install a hardened sleeve and need that measurement (it's on a different gear than the OEM one, so I can't buy and use a OEM gear). 

×
×
  • Create New...