Quantcast
Jump to content

  • Join Today, It's Simple and FREE!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

Recommended Posts

I have a 2017 can am 570 outlander max that is having issues with the powersteering going out and the speedo quits working. anyone else having or heard of these issues?  everything else on the display cluster is working and I hear no noises as far as the powersteering unit, the dealer did change the steering unit because of the recall.

Share this post


Link to post
Share on other sites


Did you ever figure this out? I've read on other forums that it could be an overheating issue or related to a needed software update.

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Topics

    • By Jun Dela Merced
      NEW HERE IM NEEDING SERVICE MANUAL FOR 2014 CAN AM OUTLANDER XMR 1000
       

    • By quadtech62
      I have a 02 Warrior i am trying to build a wiring harness i have looked in the manual and  i am confused... the pick up has 2 wires.  W/R W/G The source rotation coil has 2 wires. One is Red other is white/blue. The manual shows the  the white and blue wire connected to the w/g  right after the stator... so why is these 2 wires connected?  Does not show w/b wire at cdi 
      i have looked at many options with no luck if someone has a 2002-2004 warrior and can take a pic of the wires and location at cdi i would really appreciate it. Thanks
    • By Barry Troxtell
      I have a 2005 Sportsman 500, Instrument cluster will not illuminate, hi/lo beams work though.  Any tips or troubleshooting info is greatly appreciated!
    • By Greg van Splunder
      Any one have a diagram or engine manual on setting timing ? Had chain come off and need to know Mark's or procedure to re set timing. 
    • By Christian Brindle
      I have a 2000 Polaris Sportsman 500. A year or so ago we got it running after replacing the kill switch. It ran great but after some use for a couple months it got a flat tire and for some reason we just forgot about it and it sat for some time. Before it sat i replaced the gas cap, fuel filter, fuel pump, petcock, battery, starter relay, oil and oil filter. I recently went to start it and it started so quickly and without choke or throttle but the ATV wouldn't move till about 1/4 throttle and it wasn't really a smooth ride until 1/2 throttle. it also would bog out randomly after you came to a stop and sounded like it was getting too much fuel. I cleaned the carb and adjusted the air/fuel screw to 1 3/4 turns out.  I also messed with the idle and the throttle cable adjuster up on the handlebars. It's safe to say it now runs worse than when i started working on it 2 days ago. It takes more effort to get started and bogs out idling after about 30 seconds. I tried adjusting the idle but every time i do it'll get to a sweet spot but after driving it down the driveway and back the idle will go up and down to the point where i can't put it in gear because the gears will grind. Any thoughts or ideas would be greatly appreciated. Thanks
  • Similar Tagged Content

  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...