Quantcast
Jump to content

  • Do you own an ATV? Join our Forum!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

Gary Patch

4x4 issue quadzilla

Recommended Posts

Hi can't get my linhau quadzilla 300 e into 4 wheel drive and at time s sounds an alarm until switched back to 2 wheel drive I checked oil in front diff and fuses any one any ideas please

Share this post


Link to post
Share on other sites


Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Topics

    • By PolarisRich
      I thought I would make a quick "How-to" on setting wheel alignment since I was flipping my tie rod ends and I was going to have to re-align the wheels anyways.
      Here's some of the tools you will need...

      1.) Start with the ATV on a smooth and level surface, like a cement garage floor or driveway.

      2.)Center up (Eyeball It) the handle bars and lock them into place with 2 ratchet straps, one on each side of handle bars. This of course prevents them from moving when your adjusting the tie-rods.

      3.) Place two Jack Stands approximately 2 feet in front of the atv even with the outside edge of the two front wheels.

      4.) Wrap a length of string all the way around the ATV and Jack Stands, Start and end at the rear hitch. Make sure the string is the same height from the ground on all 4 wheels. I like to attach a few elastic bands to both ends of the string before attaching the string to the hitch. This makes it easier to adjust the strings when moving the Jack Stands.

      4.) Break lose the inner and outer tie-rod nuts. NOTE! Make sure you use 2 wrenches, one on the nut and one on the ball joint. Damage can occur by only using one wrench.

      5.) Adjust the string by moving the Jack Stands in or out untill the string just touches both of the side surfaces of the rear tires on each side of the ATV. This will take some time to get it right but it needs to be done!

      Check manufacturers wheel alignment specifications on your specific make and model before you adjust any components.
      For this wheel alignment I'm using the Polaris Specs which seems to be a common setting.
      Polaris - The recommended toe alignment is 1/8″ to 1/4″ toe out. This is a total amount, not per wheel.
      6.) On the front rim, measure the distance from the string to the rim at the front and rear edges of the rim. The rear measurement should be 1/16″ - 1/8″ (.2 to .3 cm) more than the front measurement.


      7.) If an adjustment is necessary, Turn the tie rod itself with a wrench or your hand in small increments. It doesn't take much to move the tire a long way, so go slow. Keep re-checking your measurement's until you have a 1/16″ - 1/8″ differance to the string.

      6.) Once your satisfied that you have the correct "Toe Out" measurements you can tighten up the inner and outter tie-rod nuts on both sides. AGAIN...make sure to use 2 wrenches.
      7.) Now take your ATV for a test drive to test your adjustments. If it still pulls one way or the other, just repeat the above steps to tweek the adjustments again utill your happy.
      The whole process only takes about 15-20 min.
    • By Airborne
      Hey guys been member for awhile and love this group ,kind of lost contact with social media ,i have been so busy working my property and just Racing the calender while winter is creeping in , i even slacked off Fly fishing this season , 
      As we know winter sets in and time becomes available lol, i have plenty of silly “ Quad stories to share as well as just missing the guys here great group , looking forward to winter break and tying some flys lol.     
    • By Rooftop777
      Can't figure out whats wrong, battery good, charging fine but speedometer needle flashing. I know my fuel sending unit is not working but atv was working well last year. Now it was blowing fuses. I did engine code check but none there. Gas gauge flashes and shows FUEL in capital letters. Need help as just cannot figure this out,
      I might pull the fuel pump out and put new float as likely saturated. Don't know if that would give me all these problems ??
      thanks
    • By flyinbrian365
      View File 1987-90 Suzuki LT 500R Quadzilla Service Manual
      1987-90 Suzuki LT 500R Quadzilla Service Manual. Full version clear pages
      Submitter flyinbrian365 Submitted 07/21/2020 Category Suzuki ATV  
    • By Outkast7222
      Well been lurking for a couple years, figured its time to say hey! Been riding in MN since the early 80's been on just about anything and everything with a motor. If you are from the area hit me up! Currently riding a 2018 Sportsman XP 1000, but thinking of going to a General or possibly a Maverick Trail.
  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...