Quantcast
Jump to content

1988 Bayou 220 2x4 need help to remove generator/ starter 1 way clutch cover

Monika Novakov

By Monika Novakov
in Kawasaki ATV Forum

 Share

Recommended Posts

Monika Novakov Rookie

Monika Novakov

Posted
Posted (edited)

1988 Kawasaki 220 Bayou trying to remove generator/ starter 1way clutch cover to be able to replace 1way clutch. All bolts are removed case cover is dripping what oil that remains...but I can't get the cover to come off..what am I missing? Thx in advance.

Edited by Monika Novakov
Spelling
Frank Angerano Grand Master

Frank Angerano

Posted
Posted

Welcome to Quadcrazy @Monika Novakov I’m not sure what you mean by the generator/starter ? Do you mean the left side engine cover?  The starter should be removable with a little bit of wiggling without taking that cover off. You can remove the left side engine cover to see what’s going on with the bendix/one way clutch depending on the year/model and see how it’s all operating and if anything is wrong.  If the cover is sticking maybe a little tap with a rubber mallet will help.  

Here’s a YouTube video of a 250. Should be pretty much the same. 

 

  • Like 2
  • 2 months later...

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Popular Now

  • Similar Forum Topics

    • HoldenBoy
      Starter not staying engaged while cranking
      By HoldenBoy
      Hi all,
      Looking for some help on a starter/bendix issue. Can Am outlander 450 2017. While cranking to start, the starter spins and engages into the ring gear. After a few seconds the bendix retracts while still spinning and there is no damaged teeth on the drive pulley.
    • crankin
      Starter circuit cut out relay 1997 Yamaha Big Bear 350 4x4
      By crankin
      I have a 1997 Yamaha Big Bear 350 4x4. It used to start right up. Then all of a sudden it wouldn't crank. I have a schematic for it so I started tracing the problem. I had no power at the starter solenoid. According to the schematic the power comes from the neutral switch and through the starter circuit cut out relay. I cannot locate the cut out relay on this machine.. If I apply power to the relay it will crank with the start button.
      The neutral switch is hard to get to with all the brackets on this thing. I did find out from all my research that if I apply the rear brake lever it will start.
      Does anybody know if the cut out relay exists and where it might be found?
    • marlon smith
      1990 Kawasaki Bayou 300 Intake and Exhaust Pop
      By marlon smith
      1990 kawasaki bayou 300c idles fine but pops out exhaust and intake when trying to excel, will not take throttle past 1/4 , any one had this problem?
      have replaced carb twice, same thing, fresh built engine cylinder head, same as before, new spark plug, flywheel key is good, pulser test good, good spark
    • quadnut20
      Clutch mods !!
      By quadnut20
      Just picked up a 2025 Yamaha Kodiak 700 fixing to do a EPI Clutch mod to it since I dropped bigger tires on it !! Air box , exhaust , and programmer next ! 

    • kingkw
      How can I remove the tires from a 2014 Yamaha Rhino
      By kingkw
      I have a Harbor Freight tire changer. I could not get the tires off the rim.

COMMUNITY SECTIONS

ATV FORUMS

QUADCRAZY MEMBERSHIP

Be a part of best online community of ATV riders and join thousands of people who love ATVs! Share your ATV photos, videos, ATV rides, get help with your ATV and more. Not a member?

SIGN UP TODAY

ADVERTISE WITH US

FOLLOW US ON

  • Automotive Webmaster
×
×
  • Create New...