Quantcast
Jump to content


Kawasaki Bayou 300 Acts Like Its Flooding


Recommended Posts

Hey Jeff. Welcome to Quadcrazy. Was the bike running good up until a certain point and did this just happen out of nowhere ?

im thinking the main needle on the throttle slide may be set to high. But if it was never tampered with them there should be no reason to move it.  

Check that it’s not bent, check the setting on the air fuel mixture screw also.  It may be ruining a little rich.  My guess is your problem will most likely be an adjustment on the air fuel screw.  

Link to comment
Share on other sites

It's got 32,000 miles it, it's my daily driver, 35-40miles a day 5 days a week. Regular oil and filter change, new coil, complete cleaning of the carb 2 1/2 months ago. Checked timing and valve lash and chain everything is ok. It just started one day out of the blue when the weather hit 98° and it only acts up when it's been humid as a gorrillas armpit or has sat in the sun all day. If it sets 20 minutes it'll fire right off and run fine

Link to comment
Share on other sites

  • 3 weeks later...

I just picked up a 2003 Bayou 300. A cheap Craigslist find. Funny enough I'm having the same problem, it sat in the sun all day today in 90 deg heat, and it was flooding and wouldn't start. I pulled the fuel line with the petcock in the "off" position, and lo and behold gas came pouring out. Seems like these Bayou fuel valves go bad. And as it sat all day the fuel slowly flooded the engine (not sure if that's even possible?) 

Anwyays I put an inline fuel valve on it so I could be SURE that the gas is off when it sits in the sun, and a new plug, and it fired right up... So you might check your fuel lines and make sure they aren't dumping gas into it while it sits. 

Mine is also running really rich, which is a story for a different thread

Link to comment
Share on other sites

  • 1 month later...

Update time, 5 weeks in and still no joy. New carb, fuel shutoff and cdi and still ain't getting spark. It's not the coil cause I took it and put it on my bosses 300 and it fired right up. Put it on mine and got power to the coil on the red wire but no spark. Friend of mine that works on small engines said it might be the igniter or something called a pulse-something or other. Theyre supposed to be inside the case behind the recoil starter. I'd complain but parts so far have only run me about $350 and I got the ride for free in great condition over a year ago. Still though I'd like figure out this spark problem, ideas?

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Forum Topics

    • By Spritee1
      having an issue with the unit when running under a load up a hill or in high gear, seems like the belt is slipping, there is a clapping sound coming from the primary clutch like it releases and snaps back in. i don't think I should have a noise like that. this is a friends unit and he has already replaced the primary twice with the same result.
      not sure where to look next
    • By hardcastle
      My friends KQ 300 starts fine and runs, as soon as you put it in gear and try to accelerate its bucks and farts like crazy, not moving... I cleaned carb and it worked good for 1 day... now back to same problem.... could it be such as a bent valve????
    • By Suzukiquad
      If you had to choose one mod that you couldn't live without, or had to recommend one what would it be? 
    • By BenJammin
      I did a compression test on my 2005 Bombardier Traxter 650 CVT and it's 75 PSI.  service manual only talks about leak down test.  No specification for engine compression the manual.  What does 75 PSI tell me?  Thank in advance.
       
      A little history of this machine.  640 miles.  Picked it up about 2 years ago, not running. Probably the computer.  Tested all circuits and confirm it was the computer.  Long story short, I watched a Youtube video and fixed the computer. ATV now started and runs.  BUT, it tops out 20 MPH.  I cleaned the carb 3 times also using a Mikuni carb kit after the second time.  Slide in carb is going up and down.  Only adjustment for fuel is at 1.5 turns out.  NGK Sparkplug had soot on main part but brown on the electrode.  Champion sparkplug is brown.  I check CVT clutches and they both appear to engage like they suppose to.  Checked valve clearance it's 0.00, I can't get any feeler gauges in-between.  I check timing chain I believe it's in the correct position and hasn't skipped.  I removed muffler plug and drilled into muffler to try and make sure it wasn't plugged.
    • By ResQ91
      Hi Guys!

      New member and could really use your advice. I would have to believe this has been an issue for others but a search here came up with nothing......? (Probably me not doing search correctly)
       
      I have an 87 Big Bear 350 YFM350FWT
      The OEM Mikuni BTM carb is shot and would rather replace than rebuild.
      It is no longer made and I have had good luck with NICHE carbs so I ordered a #K-CRB-0006 This was what they said was replacement when ordered. This Carb only uses 1 Throttle cable. The Slide is linked so it uses one. (OEM had 2nd cable coming through top to move slide)
       
      Problem is when I ordered a replacement Cable from NICHE (#C-CBL-0061) the Cable wire is a little short, not allowing Throttle to return all the way down to Idle position. I called NICHE and they are at a loss. Haven't gotten back to me after 2+ weeks.
       
      What would you recommend other than a carb rebuild?
      Can I just use 1 of the OEM cables (It is the right length) and snip/disconnect the other that went to top of Carb for Slide?
      Or ??
       
      Thanks in advance for any advice you have!!
       
      Dave
×
×
  • Create New...