Quantcast
Jump to content

Recommended Posts

Posted

I finally decided to pick up a pressure washer a couple of years ago, a little electric Ryobi 1800psi (test reviews show it actually closer to 2000)... no regrets. It does a phenomenal job with the big stuff, though you do have to be careful depending on what power unit you have -- I've lost a couple of decals to mine!

Posted

I use a pressure washer I bought from Amazon, and a 1 gallon container of car wash from Auto Zone. 

If your looking to put a shine on your plastics try using Quick Shine by Holloway House (sold at Dollar General). I’ve tried a few different products on my plastics but the Quick Shine has to be the brightest and longest lasting shine I have found yet. Makes the plastics look like new. 

6067FCD1-543D-4961-80C2-24303E5AB6E7.jpeg

  • Like 1
  • 2 weeks later...
Posted

I use bleach in a spray bottle from the dollar store to get oil and grime off! cafeful not to get it on any rubber or plastic because i read it has the same drying out effect as intense sunlight

Posted

i never tried a pressure washer because our shop doesn't have a inside or outside water tap on the outside shop wall... even though we do have a pressure washer//

How well does the pressure washer work on getting oil and grime off?? My dad says the pressure washer could water blast out the Chain Lubrication fluid and (expletive removed) up the motorcycle chain///

 

i know that when i use bleach $3 dollar store 'Mildew and rime remover" it turns the oil and grime into a smeary smudge i wipe away with higher quality microfiber clothes(these microfibre cloth rags just work way better)

i put the scrub free '$3 Dollarama dollar store solution' in the other Dollarama $3 sprayer bottle because it is was way better for spraying bleach (do not get on any rubber or plastic i read it will weaken it and make it brittle

(i spray the bleach on the oil and grime carefully and aim it real careful and then i use a giant flat head screwdriver and a medium flat head screw driver /one in each hand i attack and poke and scrape on the bundled up microfibre cloth on the grime to smear and wipe away the grime oil smudge (these clothes work very good at absorbing and hanging onto all the smudge

scrub free.jpg

sprayer bottle (1).jpg

microfibre rags.jpeg

screwdrivers.jpg

Posted

I use a foam cannon on my pressure washer and soap called Tuff Mudder 

they say it leaves a coating that keeps the mud from sticking 

however I will be trying the purple stuff on the engine 

  • 2 months later...
Posted
On 12/5/2021 at 12:03 PM, Crashman said:

I use a foam cannon on my pressure washer and soap called Tuff Mudder 

they say it leaves a coating that keeps the mud from sticking 

however I will be trying the purple stuff on the engine 

how does the Tuff Mudder work?

  • 3 weeks later...
  • 2 weeks later...
  • 4 weeks later...

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.




  • Similar Forum Topics

    • By Maxg_57
      Is anyone still active on this club
    • By BillR94
      I picked up this ATV that had no spark. The previous owner said he was driving it and it died and would not start. He discovered it had no spark. He replaced the CDI and the coil with no luck. He got tired of it and I bought it. I replaced the stater and now it has strong spark. Now, it starts for a second or two then dies. It will not stay running. I have checked the timing and it is spot on. The valves are adjusted correctly. I see no warn issues with the cam. I put the original CDI and coil back on it. Same problem exists. Compression is at 65 psi (has decompression mechanism),
      I took off the muffler in case the issue was clogged pipes. No change. I replaced the spark plug. No change. The carb was an aftermarket so I put a Niche carb on with no change. I bypassed the fuel pump and that did nothing to solve the problem. 
      I don't know if this is a carb issue or an ignition issue. I am looking around locally for an OEM carb to try out but not sure that will fix the problem. 
      Can anyone help me solve this problem. I am running out of ideas. 
      Thank you for your time
      Bill
       
    • By hunky
      This old boy has been coastal so lots of rust. But when I turn the key, nothing. Green neutral light works, head/tail lights work. Was running fine when I parked it for a few months.. no issues with starter. This did happen once before (last year).. not sure what overcame it.. maybe playing around with gear shifter.. but not sure if that was what did it. But doesn't seem to do anything now when I play around with it while hitting the start button.
      I did take apart the handlebar mounted start button housing and looked it over. Couldn't figure anything out there, but looked the same as when I had the problem last year. Put my probes on various wires there but didn't learn anything.. not sure how it is wired.
      So this first image there is a connector with 2 wires coming from forward (the male part of connector) - one blue and one blue w/ red stripe. The blue continues down to a post near where the gear shifter enters the housing. (Second image). I was wondering about that.. I opened up the connector and the 2 wires (coming from forward) show continuity when I put my probes on 'em. Thought that was weird, but maybe supposed to be like that? I turned on the key and tested for voltage but didn't find any.
      I'm just unaware of how to test for anything. Would be interesting to put 12 volts to the starter, but not sure about doing that or how. The wires going in are kind of hard to get to. I suppose I could take out the starter.. but wanted to ask if there is something easier to check first.
      Thanks for looking!
       

    • By 97kingquad
      Okay so I bought this 1997 sazuki king quad from a guy and he had it for a few years. 
      He had it registered and on the trails last year but he said it bogged and backfired when he would try to drive it. so it sat for a year. 
      I bought it for 800 bucks and got it running that night and it ran great for a few days 
      But I parked it the other night and went to start it again and it was really hard to fire up and when I did it was bogging and idling high then low again.
      So I took the carb out and cleaned it (ended up doing it twice because it was still doing the same thing) 
      Now today I have it running slightly better, but it is still like 20% 
      I have been looking it up and trying to figure it out but I can't find the issue, has anyone else had this problem? I'll attach a video of it running and giving some throttle 
    • By davefrombc
      It would be  helpful at times to have a button  where we could cont the Admin. to  make some changes to  our posts.
×
×
  • Create New...