Quantcast
Jump to content

  • Do you own an ATV or UTV? Join our Forum!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

STOLEN ATV: Stolen 2000 KTM EXC


Recommended Posts



Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Topics

    • By Wagnerc
      Are the tires on Amazon worth getting? Wanda and Kenda are two I was looking at
    • By JacobSlabach
      So this’ll be long I’ll give all the background first to see my issue skip to the ***
      Hey I picked up a pit bike and a foreman for 800 the pit bike was running but the foreman was locked up.  Sold the pit bike but when I took the top end off the piston I only found half a piston left.  So knowing the rest of the piston was down in the crankcase I knew it had to be pulled and gone thru completely.
      to pull the motor I went ahead and pulled the rear end off and unbolted the front diff to pull the drive shafts and pull the motor.  Now I have the motor torn down completely and have all the parts of the piston removed.  I know the rod and crankshaft is shot (heat discoloration and too much up and down play rod to crankshaft).  
       
      ***so I’m wondering while I have the motor apart what should I check for?  I know this motor died from heat as the oil in the head smelled like popcorn.  So what should I check to make sure I fix the issue (overheating I assume) and not just the symptoms (blown up motor lol).
      so put simply I don’t want to just rebuild the motor to have it overheat and repeat the process after 5mins of running
      Here’s some pics





    • By Quad king
      I am not sure what is wrong with my King Quad. I had a new carburetor put in 6 months ago, just replaced the fuel pump and added an in-line fuel filter in. I have been trying to fix this quad for a while now and do not know what is wrong with it. It idles fine and runs great as soon as it is fired up, you can Rev it and stay in first gear with 100% power. As soon as I drive 10 feet it looses all power, I mean it is sputtering and doesn't move at all, but when I let off the gas after it sputters it idles fine. I will attach a video of what it is doing.
      Snapchat-1290161440.mp4
    • By Brennon Heflin
      So I bought a 2000 quad runner 250. I'm having some issues an wondering what it could be I replaced the pet cock valve an the fuel filter an pump inside tank I also put a voltage regulator on it. The problem I'm having is that when u give it half or more throttle it bogs down an loses power what could it be the bike is almost like new an cant figure it out any help would be great
    • By cfauvel
      ok help so according the service manual, Idle Air Mix Screw (aka Pilot screw) should be initially set to 2.5 turns out from fully seated.

      If I do that the motor doesn't want to start or stay running...right now the pilot screw is probably somewhere near 5 turns out....I'll take the carb off tomorrow to count to know for sure.

      mind you the carb got a new float seat,float needle and various other components in the kit.

      To get the motor running I hard to turn the pilot screw out quite a bit, and turned the idle speed screw in quite a bit...I didn't hook up an inductive tach to know what it is idling at, but does sound about right.

      What should the idle speed adjustment screw initially be set at (the one that has the black cable sheath with a knob you can twist easily)?

      Is there a special tool to turn the idle/pilot mix screw whilst the carb is on the running motor? I am using a slotted screw driver bit (normally goes into a driver) by hand..makes it hard to turn the driver and hard to tell how many turns .
  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...