Quantcast
Jump to content

Recommended Posts

Posted

Question: Do you have to take gas tank off to get carburetor off the quad. ?? 

It's gummed up again and needs cleaning. Put Sea foam in tank hoping it would dissolve any crud. No joy

Posted

You don't have to take the tank off.  Sometimes it makes life easier but it should be able to come off without taking the tank off.  I like to loosen both clamps first.   Disconnect the gas lone, pull the carb out so you can take the throttle cable and the choke cable off.  Re assemble in the same way.   

Posted

Ok. Sounds good. 

I seen something about loosen clamps and turn to take bottom off float to change out jet.  Would that be enough to get out what's gumming it up. ??

Any videos you know of ??

Thanks for your reply

Posted

Honestly heres my take.  If its at the point where you feel its bad and a possibility that the  tank my have skunk gas as well then pull the tank and clean the carburetor and tank properly.   I've very rarely had luck by rotating and cleaning the carburetor in place.  You only wind up pulling it all out again. 

  • Like 1

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Forum Topics

    • By LMI
      Hi all.  New to the forum & quads.  Seems like a great place full of info.
      I just recently picked up a 2005 Suzuki KingQuad LTA700.  I need a battery.  I've been reading up on conventional vs AGM types.  I have a Royal Distributing and Canadian Tire.  RD has 2 types avail for my year/Model a battery YTX16-BS CRANK $75, and BATTERY YTX20CH-BS YUASA $140.  Neither of these is the type from the manual FTZ16-BS.
      from what I can tell... I think the only difference is the capacity with the $75 unit rated at 14 AH/10HR and the $140 unit rated at 18 AH/10HR ... which is the rating in the manual for the FTZ16-BS.  How much does this make a difference for nearly x2 the cost?
      And about the models/type numbers.... what is important to know ... they all end in "-BS" but are the other details relevant or just manufacturer naming?
    • By rjsummer
      Just picked up an 84 LT185 ATV, I understand there was an accessory add  on that gave it electric start, anyone have any info about that kit? 
    • By sandman001
      Just picked up a 2006 Dvx400. There is a switch I can't figure out what it is or where it goes. Has 3 wires (light blue, black and Yellow)

    • By kawasig
      Hello there
      I'm having a problem finding a quality carburetor for a 1993 Suzuki Quad Runner lt-f 250 2x4. I find a lot that have 3-4 star ratings. And all so far don't have the right throttle Cable inlet at the top. The last one I got 4 star on Amazon has a threaded cable sheath rest that could be partially drilled to work. I would prefer to get one I don't have to modify. Any recommendations are greatly appreciated!
    • By fixitforfree
      I have a 94 Trail Boss 250 2wd that will not go into forward. Reverse works great but forward just clicks but won’t engage. I’ve verified the shift lever is pushing far enough so I believe I have either an engagement “dog” or mating forward gear that are likely bad. I also see a fair amount of metal on the dipstick magnet. But if I ride the machine in reverse the gearbox seems quiet with no other issues by what I hear. That said I’m in process of pulling the gearbox to see what parts I need. The gearbox has 1341124 as the model number as shown in the photo below but I can’t find any gearbox on eBay or the Polaris parts site that matches that number. Is this 94 model a year that used some special gearbox? My tag on the box even looks different than all the tags on gearboxes I see for sale on eBay. I really want to buy new parts for the ones damaged in my gearbox to fix the one I have but just doing research at this point to see what gearbox I have to know which parts I need. Anyone with experience with this I welcome some advice or direction from what you have learned. Just FYI this machine is new to me but cranks, runs and idles perfect. It’s not beat up and will be a gem when I get this tranny fixed. Thanks.

×
×
  • Create New...