Quantcast
Jump to content

  • Do you own an ATV or UTV? Join our Forum!

    As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.  Registration is fast and you can even login with social network accounts to sync your profiles and content.

2018 Sportsman 1000 cam timing help.


Recommended Posts

Had a spark-plug break off, had to pull the head to get it extracted. Where the heck is the timing mark on the crank? Do I need to pull the stator or flywheel to find it? When I pulled the head I had the mark on the cam lined up pretty good but I cant remember if it was perfect and don't want to reassemble a tooth off and have to go back through the bear of pulling this thing back apart.

Thanks guys!

Link to post
Share on other sites


Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Tagged Content

    • By jwline
      Friday evening went riding, rode for a good hour or so everything was fine. I went to take a short ride to the restroom (less than 100 yds away) and all of the sudden everything flickered and then just died out. Accompanying the problem I noticed the killswitch completely locked up. Once daylight hit took the killswitch apart to find it had shorted out and melted the plastic inside. Has anyone else had anything similar to this and if so what did you do to fix the situation? I have a new killswitch on the way to replace the obvious problem but was wondering could there be a bigger issue at hand. We tested with a voltage meter to make sure everything was still getting power from the battery and as far as we could tell it was.
      Any advice/info would be GREATLY appreciated.
      Thanks.
    • By bodon
      Anyone know what the fuse terminal marked UNSWITCH  does  .  Even with the key off it is causing a drain on my battery and I'm trying to figure out  what that terminal goes to.  It's a 10 amp fuse. If I pull it the "short" goes away.  Thanks in advance.
    • By Chase Cook
      Hi I just got an Polaris sportsman 500 4x4 ATV the other day. I got it real cheap but I started to go into it because it didn't have compression so I bought a new piston and ring kit for it and installed it, but now when I try to start it all it does is shoot fire out the exhaust or the intake of the carburetor. And a timing is top dead center.;I think I can't really tell another way if it is or not. when I put it together I made sure to piston was on top and the cam lobes where facing down where are the cam sprocket is facing up. It has gas and spark. It did start a couple minutes ago but it didn't stay running and now it won't start. Do you think the valve need to be adjusted more to close better?I'm fixing to try that out and if that don't work what is the problem? Also I made sure everything was together good and right and change the oil and changed out the radiator fluid.
    • By Brian Sosebee

      I just rebuilt my 03 sportsman 400. Put everything back together added oil per the manual. Pinched off the oil tank vent line 2" away ran for 45 seconds then cut it off. Check oil level and it was still way high so I wasn't confident that it primed so I did it again. Checked again and it's the same. Remove the oil filter and it is dry. I did the procedure again and the same results.

      I'm worried to keep trying this as the only oil in the engine is what I used to lubricate the parts when reassembling the piston. The crankcase was drained as well.
      I Removed the oil tank and checked all the lines for obstructions and the screen filter and the vent hose and everything is clear. I even pulled a small vacuum on the oil tank while it was pulled off to make sure there were no leaks. The dipstick cap was on tight so I'm not sure why this thing is not priming.

      Anyone have any suggestions. I thought about pre-priming the oil lines from the oil tank to the crankcase to hopefully help the system prime. I'd like to be able to add some oil to the crankcase to so I wouldn't feel so bad about running the engine for another 60 seconds without oil. I dropped just a little bit of oil in the spark plug hole to help condition the sleeve right now.

      What do I do? Anyone had or heard of an oil pump failure on these. Btw oil pump is working fine before I did the top-end rebuild and the oil pump was not touched.

      Please help!!! Thanks all for any and all help.
    • By jay rear
      Hi im new to the site. I have a 99 sportsman 500. I has been sitting for about a year now. I bought a new battery for it the other day and now i dont have any power to anything but the winch. Any help would be great. I already cut the pouch and checked voltage on both sides of the circuit breaker. 
  • Similar Topics

    • By bigboy123
      When running for a while the rancher will shut off without the fan turning on. We then took it to dealer where it was started and warmed up. The fan came on at the dealer so they then replaced the fuel filter and fuel pump. We got it back and ran good for a few days with the fan coming on when needed. Now its back to shutting off before the fan ever comes on. It seems like the time the fan should come on the bike shuts off. It will start after letting it sit for a few minutes. Any ideas of the problem? 
    • By diamonddogs
      Hi i bought my first atv last week, mostly for plowing. its a 94 yamaha big bear 350 4x4, with plow, new front axles, carb rebuild and some other stuff for $900. in todays prices, i think it was a pretty good deal. I plan on tearing it down and doing a semi restoration in the summer. its been clearly neglected so i suspect i will need to do a fair amount.
      couple questions. 
      1. parts and manuals, so far i know it needs front shocks, tie rods, brakes, cables, lots of small stuff, whats your guys favorite online atv parts store? where can i find a good repair manual?
      2 - starts and drives great, shifts a bit hard? not sure whats normal because i dont have a point of referance. i have to almost lean back in the seat and lever my foot up to get it to shift, seems like there is either alot of play in something (shift lever itself is tight) or there is a long travel, or it just dosent want to shift. also the hi / low / reverse lever needs to go past the gate a bit to actually shift into gear, and seems to need me to shift into nutral before shifting into reverse (not sure what your supposed to do). also wondering a bit about the history of the machine, because the plastics have a slot for a dash mounted shifter, but the one on it is a gated shifter right above the pull starter. 
      3. seat and plastics repair, seat is quite torn up with a seat cover over it, plastics are pretty cracked up, these items i havent found replacements for for any reasonable price, i dont care a whole lot about asthetics but whats the best way to functionally repair these things? is there reasonably priced replacements somewhere? i plan to bedline the whole thing after im done. 
      4. there was no title, but i did get a bill of sale, will it be difficult to get it titled / registered? (im in mn)
      thanks in advance for your help, looking forward to being part of the community

    • By Scrambler54
      I'm new to this sport and would like to replace the factory tires on my 1995 Polaris Scrambler 4 x 4.  Any suggestions and where is the best place to get them would be appropriated.
    • By 3wheelerwarrior
      Hello folks, I have a yamaha timberwolf 250 motor I'm putting into a tri moto 200 frame and need some help with the wiring for it. The wiring harness I got with the motor has been damaged and missing a small section so my issue is that I have 3 white wires coming from the stator assembly which connect into another 3 white wires on the voltage regulator. My question is does it matter which of those white wires go connected together or are each of the white wires different and need to be connected to the appropriate wire on the voltage regulator. Any advice or help is appreciated. Thanks.
    • eManualOnline
    • By Muskyjim
      I recently purchased a 99 big bear 350 2x4 that was sitting for a while got it running and went to take it for a ride after about 10 minutes into the ride it stalled and wouldn't let me shift down into neutral tried rocking it back and forth but will not go into neutral...can anyone point me in the right direction on where to start?
  • Recently Browsing   0 members

    No registered users viewing this page.


×
×
  • Create New...