Quantcast
Jump to content

Recommended Posts

Posted

So my 2006 Honda 350 fm is having an issue where the neutral light doesn’t come on. I’ve shifted into neutral, checked all the fuses, the battery is good and still no neutral light comes on when I turn the key. I found the neutral safety switch connecter and hooked an alligator clip to the green and red striped wire and put the other end of the alligator clip to the negative side of the battery and nothing happens. I put an alligator clip to the gray wire and put the other end to the negative side of the battery. Nothing happens. I can put the alligator clip to the positive side of the battery and the reverse light on the dash will come on. I tried doing the green and red stripe wire to the positive side of the battery and the light doesn’t come on that way either. So neither the negative or positive side of the battery will turn the neutral light on. Only the reverse light works but only on the positive side of the battery. The ohm meter will only read continuity on the gray reverse wire. Not getting any kind of reading on the green/red wire.No continuity just a big open line reading for thegreen/red wire. Is the neutral safety switch brokeN? 

  • Admin changed the title to 2006 Honda 350FM Neutral Light Issue
Posted

Bulb is good just changed it. Just noticed that the reverse light only comes on if I hold either the left or right brake on the handle bars. But the gray reverse wire has to be touching the positive battery terminal and then I’ll hold the brake lever and it lights up. 

  • 3 weeks later...
  • 5 months later...
Posted

Had the same issue on a suzuki , reverse light worked but not the neutral, took the "sender" apart and it was filled with oil, so the contacts where burnt.

My advice is to remove it, measure it on the bench first, maybe try and clean it inside with some brakecleaner. Make sure it isnt binding in anyway.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Popular Now

  • Similar Forum Topics

    • By Joeguy
      After i did my rebuild it seems to not want to shift well. I think the cable is alright, and when it does shift its nice and solid. I have to basically use my hand to shift and i have to pull or push it very far, like max travel, to get it to shift. I also tried adjusting the clutch set screw. Any ideas where to go next, or maybe i should just grab a new cable to try.
    • By jen
      Wow...I packed a small soft side cooler with an ice pack  at -4 F and inserted my Type K thermocouple sensor inside so I could monitor the temperature without opening.  After 3 hours  the inside temperature was 60  F...OMG!   The ice pack  was solid frozen.   Standard temperature for safe storage is < 40 F.     What I found by asking was that there should be no air space in the cooler.  Packed with Ice preferably ice from connivence store (normally 0 F of less).  Food should take up  short day trip1:1 ratio.
      Good coolers are expensive.
    • By Cj Winds
      I have a 2009 Honda Rancher TRX420FA with shifting problems.
      Usually it shifts ok when cold but after couple minutes it will stop shifting with no codes.
      The 1st shift clutch oil pressure when in first gear is 74psi. The 2nd shift clutch oil pressure when in second gear is 74psi.
      The 1st shift clutch oil pressure when in neutral is zero. The problem is when the tranny is in neutral the 2nd shift clutch pressure starts around 10-15psi and builds to 20psi. Is this normal?
    • By OldATVowner
      Just getting into this issue really. Been replacing solenoids but now I'd like to track down the problem. This time I'm not getting neutral/reverse lights or start button. Was on a creek ride when it started doing this recently. It cranks by arcing the solenoid and gives me no light or start button but if I crank with the pull cord....the neutral light and the button work. Turn it off and try to crank with the key and nothing. I'm looking into the safety switch issue tomorrow and re charging the battery. Just figured this was odd enough of a problem that you guys might be familiar. Thanks
    • By Dsluder
      I am having an issue with a hs500. I bought it broken and have been trying to get it running. It seems to be starving for fuel. If I put my hand over the intake it will crank but will not run for very long because I'm not able to get the correct airflow with my hand. The things I have done so far are. Replaced the fuel pump, fuel filter, mass airflow sensor, idle air adjuster, fuel injector, cleaned the throttle body, replaced the ecu, and still the same issue. I notice the injector does not spray when removed from the head. I dont know if that is common. 
       
      I am out of ideas on what to do next. I have removed the fuel line from the injector and it is getting plenty of fuel. If anyone has an idea on what could possibly be the issue I would be happy to try anything at this point.
×
×
  • Create New...