Quantcast
Jump to content

Recommended Posts

Posted

Hey, this is just an FYI post.  After getting my quadrunner going again (voltage regulator issue in other posts), it ran well, but a couple of times I had trouble getting it started.  I suspected the fuel petcock because I was shutting the fuel off when I wasn't using it, and I knew the filter/stems in the tank were looking rough last time I shone a flashlight into an empty tank.  So I went on amazon.ca and bought the cheapest petcock I could find, like $13.99.  But when it arrived, I realized it was different than the original.  It had on/res/pri as the level selections, and along with fuel out, had a connection for (I discovered) vacuum in.  Wheras the original petcock only had on/off/res and just fuel out.  So I read up on it, sounded cool, the vacuum connection means that you just leave the lever set to on, and it automatically cuts fuel when the engine is off.  So I found a splitter, and I split vacuum off my fuel pump to the new pet cock, and it seems to work well.

 

I'm not sure if I've made a mistake here, but I like the idea of an automatic fuel shutoff, and if there's an issue, I can just set it to Pri, and it bypasses the vacuum shut off and just allows fuel to drain through the lower Res stem.  Only thing was setting the lever to Res, I expected it to work the same as On, but fuel coming from the lower Res stem, but it doesn't seem to allow fuel at all, but not a big deal since Pri will serve that purpose.

 

 

Posted

Standard taps have on-pri-res. The prime being horizontal.. And yeah, reserve normally works the same as on, under the control of vacuum.

 

Might pay to take the rotating part of the tap out, and check the washer behind it is located correctly..

Posted

It will probably work good for many years, I have one on my Eiger that's bad I turn it to prime to fill carb for a minute  and turn it to on I start it after a few minutes it runs out of gas, turn it back to prime and it runs again, I wasn't sure if reserve was vacuum operated because reserve works but on does not. 

Posted

Some early 250 suzukis had a mod which was to fit a little capsule/filter/valve thing into the vacuum line to the tap. The capsule allowed full vacuum to the tap instantly, but had a restriction in the flow going back the other way, so the tap was slow to close.

That might help your new tap...

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Forum Topics

    • By docdoug72
      Has anyone had a suzuki 230 quad lock the engine up?  Its a well maintained bike, it locked up when my son was riding it. Pulled the plug, it has connected with the piston. I'm thinking the con rod let go.  I don't have a service manual.  Does the engine need to come out to check further?
    • By kawasig
      Hello All
      I'm kinda new to ATVs. I just bought a 1987 Suzuki quad runner 230 Dual Range. I'm having a problem finding info on it. It's very clean, only 2.800 miles. The front wheels are only 30 in.center to center. I was thinking about adding wheel spacers to give it more stability. I realize the added stress on ball joints and bearings. I'm wondering if there are any other concerns? Any input is greatly appreciated!
    • By Dumass
      My name says it all. I have a '03 Honda Sporttrax 400EX with a new aftermarket carb on it that seems to be having issues. I can start it but it idles really rough and when I give it throttle it just kills the engine. I have tried adjusting the idle screw but to no avail. I am in the San Diego Ca area. 
      Any advice will be greatly appreciated. I would also like to get an owners manual for the thing too but can't seem to find a downloadable one.
    • By fwsamm
      Im aware that this relay needs a positive (+) and a negative (-) to activate the other side. The blue wire is the neutral wire so when in neutral it gets ground. The green wire is from the parking break; when you pull the break in it gets ground (-). however one of those two needs to be neutral so that the positive from kill switch can go to the starter relay. The ground from the starter relay is from the start switch. Which one (neutral or parking break) should have a positive (+) voltage?
    • By DPDISXR4Ti
      I hadn't driven my Kodiak for a two months, and since it was low on fuel, the first thing I did was filled it up to maybe 7/8 full. Getting ready to start it, I rotated the fuel selector switch to "on" and within seconds I smelled and saw fuel dripping onto the floor. I quickly turned it off and the fuel gradually stopped - I can repeat this.
      The fuel is flowing from the hose that is connected to the bottom of the carb, and routes around to the left side toward the wheel well. Any idea what's going on here? It ran fine the last time I had it out.
      Thanks...
×
×
  • Create New...