-
Do you own an ATV or UTV? Join our Forum!
Join QUADCRAZY ATV Forum today for FREE! We keep these forums clean and user friendly. All first posters will have to wait to have their content reviewed and approved. Once your first post is approved, you will no longer need to got through an approval process. To gain immediate approval and a NO ADS experience, consider subsribing to our Premium Membership.
-
Similar Topics
-
By Parham
This quad was a hot mess two weeks ago when I got it. I've been tinkering on it and have it running pretty good. It didn't have a pull start. I just got one and installed it today. Here's a little video of my first try at using it. Hope it's worthy of a "onya" from Mech! 🙂
IMG_3274_Trim.mp4 -
By Am2007
Hi everyone,
Outlander 2006 400 XT i have replace the startor cover and right after i did that the oil light is on and not turn off, i check the wires and checked the oil level, everything seem to be normal quad is starting without any problem and rev just fine. i did not want to ride it since im not sure if it is faulty sensor or not so just be safe i did not let it run more the a minute or so.
I have read in the owner manual that i need to clean the oil strainer every 200hr unfortunately i never did that, my service manual that i have does not even indicate of such a thing. so i did some search around and it seem like canam split the manual into 3 parts
owner manual
service manual
engine manual
I have the first 2 but i can not find the last one, part number 219100232. If someone can guide me where do i find the oil strainer so i can clean it i will appreciate it. im going to do an oil pressure test tomorrow to check how many PSI i have, just to make sure.
Thanks
-
By DonB
Fuel Injected, 2015 AC XR550XT ATV (renamed the Alterra from 2016 on). 1300 miles.
I had written an earlier post concerning part of the problem, but a new one has arisen...
2 PROBLEMS:
Engine sputters & fails when throttle applied (even from idle and while in Neutral), and, now... Fuel pressure reads @ "0" despite clear line and operational fuel pump. Unit originally suffered fire in muffler - presumably due to engine driveability problem & resulting unburnt fuel... fuel pump ultimately died when starting repairs. Installed a new fuel pump as dealer advised it was the problem. Have now been chasing a proper fix for several months, as, while it generally starts fine, the engine will not take any sort of throttle - even from idle. Instead, it immediately starts to miss, backfire & die. From the beginning, the dealer claimed that a new genuine AC fuel pump was all that was needed. However, the replacement, non-AC fuel pump runs at 42 psi & works fine). NEW ISSUE: Unexpectedly, the first replacement pump stopped registering any fuel pressure (per in-line pressure gauge). This despite confirming both: (a) pump clearly pumping & (b) fuel line - all the way to the fuel injector - clear & delivering fuel. Tried a 2nd replacement pump which, initially, registered pressure (engine performance issues remained). But, when I tried to start it today, no fuel pressure again (and, therefore, apparently no fuel to injector). Again confirmed pump working and fuel line to injector clear & delivering fuel. Engine continues to start easily with starter fluid but, of course, stalls once fluid has burned off. While cleaning/replacing the fuel injector seems the next logical step, it strikes me that, were the injector plugged, I should still be seeing a psi reading on the installed, in-line gauge I've been using (not zero)!
Any ideas before I surrender this to the dealer and a B-I-G bill?
thanx, db
-
By hporter1208
Okay, so I have a 2002 Rubicon 500…bought it last year and it sat for several months until I put a new rear axle in, FINALLY got that done and was super excited to finally have my wheeler going, just to notice a strong gas odor. Popped the seat off and sure enough, pouring gas from the carb overflow. Fast forward a few more weeks and get the new carb and get it in, no leak! Yay. Except now I have no spark. 😒 I’ve tried another plug and checked and am getting no power to the coil pack. I’ve read and read and mostly what I’ve found is ECU, which is fine…but I like to exhaust all avenues before buying the more expensive parts just because I don’t wanna spend the money and it have ended up being something simple that I overlooked because I was trying to rush. 😂 I don’t know if it’s relevant, but I read on another post that someone had similar issues with theirs and it was the sensor on the side of the carb, just a thought since this literally happened after I put the new carb on. It also displays “- -“ on the display screen where it should show the gear position.
-
By carlneedwindshield
Hey Guys, we are looking for some good windshields and back windows for some customers and we came across Flex a fab as a manufacturer, does anyone know about their products?
-
-
Similar Tagged Content
-
- 16 replies
- 507 views
-
- 2 replies
- 328 views
-
2019-2020 Yamaha Grizzly 700 EPS 4WD Service Manual
By GrizzlyRider,
- grizzly
- grizzly se
- (and 1 more)
- 0 replies
- 821 views
-
2019-2020 Yamaha Grizzly 700 EPS 4WD Service Manual
By GrizzlyRider,
- grizzly
- grizzly se
- (and 1 more)
- 0 comments
- 2,064 views
-
- 2 replies
- 1,114 views
-
-
-
Gallery Images
-
-
Recently Browsing 0 members
- No registered users viewing this page.
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.