Quantcast
Jump to content

Recommended Posts

Posted

have a raptor 660 that is doing something a little weird. If i just go along slow it is fine but once I put some pep in it the thing seems to skip every 4 seconds. At first I thought the chain was slipping but I can not see any wear or visually see it slipping. When it does it there is a loud clicking/clanking going on. The weird thing about it is that it does get up and go and will accelarate even while doing this. Any suggestions?

Posted

It seems to be. I by far not a mechanic but I am mechanically inclined. I can go and shift through all the gears and pick up some major speed. It seems to do it in every gear. I am pretty sure it is in gear fully but do not know the correct way to verify besides knowing it has pep and goes with lots of torque.

Posted

Thats what I thought so I loosened it up. I do know I have an issue with the rear end because the axle has about 1/4 to 1/2 inches of play in the housing. Another hint that might help is sometime when I stall it out (not that I would ever do that on purpose hahaahha) when the engine stops I hear something like a hammer slam the engine.

Posted

ok that might explain the kicking when stalling. But when I am giving it some gas and really putting the pedal to the metal the slipping/slapping sound must be a major issue. You think needing a carrier bearing could cause this?

Posted

I dont know why I am even telling the truth about what the problem was because it was so obvious and I didn't think to check it. After beating the hell out of it on the track i found that my front sprocket was worn down. I knew it sounded like the chain slipping. Thanks for everyones input.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Forum Topics

    • By Yamahahahaha
      I'm in the middle of repairing damage from the chain coming off of this from the previous owner. (I learned this is somewhat common on these for various reasons.)
      What are you guys using to either help keep the chain correct and on the sprocket or guarding your engine in the case that it comes off / breaks?
      Is there an upgraded guard that can bolt around the sprocket in replacement of the currently broken OEM alluminum?

    • By Gtc4d
      I recently purchased a raptor 80 for my grandson for  christmas. I am trying to make sure it is running properly. i have rebuilt the carb and adjusted the carb idle then the mixture to middle of where it runs rough and it runs great for about a min or 2. then it stalls out. I can usually choke it and it will start so i feel it is lacking fuel. the fuel shutoff valve has been changed and i checked it for good fuel flow.  any ideas of what to check next. I am planning to vfy fuel float height tomorrow. I visually checked it by turning carb upside down when i had it apart and it looked level. any ideas are appreciated. 
       
      Thanks.
      Todd
    • By P_syko
      Which is more reliable? Shaft or chain drive? 
    • By jordan_ATV
      I got a 2005 350 Raptor Special Edition and I'm dealing with a no start issue; the weirdest thing is when I'm cranking it fires and slows down showing signs of pre firing, smoke shoots out the carburetor every time it sparks. every electrical part (CDI, Rectifier, Stator, Coil) has been swapped out from previous owner, the top end of the engines all new and I cleaned the carb out, anyone got any ideas or similar problems, also is it possible to have a bad spark timing
    • By AnthonyT
      In search of my first ATV? What are good older 4x4 models?
×
×
  • Create New...