Search the Community
Showing results for tags ' raptor'.
-
Hi, I'm a new member Just bought a used 08 350 raptor with about 5 hours on it ( very clean ). Started fine when we got it. Now after a few mods (bumper, skid plates, air filter) Now will not start unless you pull in the clutch. I've checked just about everything and also checked that there is no pinched wires. Anybody have any ideas?:bangheadc: Thanks, Dave
-
well, i got a 06 350 raptor se and was riding one night and it just shut off so what im asking is can any one tell me how to test the cdi,rectifier,or any other componet test it has no spark and what i did check was power from cdi to coil and none any test would help it is that the bike is 3 years old and solid state parts should last alot longer but everyone knows that it happens any help would be great and yes the fuses are good thanks in advance for your help
-
Hello, I'm new here to this forum and have a question for ya on my 05 raptor 350. After about 10-15 minutes the engine does not want to idle. After adjusting the idle screw, the engine will run, but now the idle is really high. When riding after the warm up period the engine pops, sputters, and ocassionally backfires and dies. It acts as if the fuel/air mixture is wrong but unlike my two stroke there is not a fuel/air mixture screw for adjustments. Any suggestions??? Thanks Steve
-
I have a 01 raptor and recently had to bore it out to a 686 because it sucked in a bunch of sand. Now I have no torque or power in the first third of the throttle. I am hoping that someone else knows what is going on with it
-
Hi! I own a 2013 Yamaha Raptor 125. Got it last week and im planning to upgrade some parts. Hope you guys can help and give me some tips. thanks!
-
Hey guys an girls I need a little help. I bought a new carb for the wife's 350 and it runs good. It just doesn't seam to have the same power it did before I changed the carb. I bought a GYTR jet kit pt#gyt5yt980000 it's just main an air jets. The bike is stock and I dont know which jets to start with. The kit has 2 air jets an 10 main jets. Does anybody know where To start. The kit did not come with a needle jet. I bought it off ebay and it was unopened When I got it. Any help would be appreciated ALOT.
-
Here is a new Raptor 660 starter clutch install video By L&L Extreme
-
Hi, i need Service Manual for 2004 Yamaha Raptor 350 is there a link that works to download the service manual? Thanks in advance!
-
okay so any help would be great. Can anyone tell me why my quad runs okay on reserve but when you turn gas to on it bogs down every time throttle is given. It also back fires when gas is on. I replaced the pet cock fuel line carb was cleaned and redone to resolve problem but still having issues. Any ideas?
-
So I bought a 2008 Raptor 350 off a guy for $300 he told me all it needed was a new stator. So I bought a new stator and put it in it. When I did that the fourwheeler would start and shut off. I asked a buddy and he said that when you replace the stator you replace the voltage regulator. So I got a new one one and put that in it and it still starts up and shut off when you touch the gas. But if I unplug the voltage regulator it runs good until the fourwheeler gets to a certain RPM then it shuts off. Does anyone know what the problem is??
-
Im thinking about buying a 06 raptor 700. I was just wondering if you guys could give me your reviws on it to see if its worth buying. Thanks, Burton.
-
I am looking to get a new bike this spring. Its either going to be a yfz 450r or the raptor 700r.I can pick both bikes up for the same price.So i am asking for every ones thought on what they would pick. I mostly ride trails with family and friends. I have raced gncc but that was with my 250r(how i miss her but she was stolen guess someone needed her more than me) I have a family so i am not blowing down the trails.But when i am out with friends we do like to hill climb off cambers and ride faster. Whats everyones thoughts. Any input or info would be nice. Thanks for reading and helping.
-
DOnnez moi vos avis [ame= ]Quad 700 Raptor vs 450 Ltr - Gopro hero 3 & 2 - YouTube[/ame]
-
I have an 03' 80cc raptor that doesn't want to start from a cold start. It turns over nice. I can put it in gear, drift it and it starts right up. After its warmed up, I can shut it off and start it up using the electric start with no problem. I cleaned the carb, put a new spark plug in, checked the spark. I put a new battery in and a new starter. The choke plate screws are still there. My friend said it might be a compression issue. Any ideas out there?
-
Howdy, I have an issue with my Raptor 700, Last weekend I was out and about and the rear axel bearing Failed... Badly!! and im in the process of trying to change the bearings, Has anyone got any Tips on how to get the old bearings Out? or where I can get a new Rear Spacer for cheap, I don't really want to spend £60 for what seems to be just a bit of pipe
-
Hey everybody! I would rather install my own blinkers, relays, wiring rather than buying anything for $200. Can anybody point me in the right direction for a nice guide possibly. Im planning on lowering it and doing anything to make it more stable on the pavement...so if you have any suggestions there as well they will be greatly appreciated. So far i plan on buying the Duro Scorcher tires and G-Force XC-1 wheels. All stock size CRJ lowering kits Anyways i want this focus to be on wiring in turn signals and a horn. Thanks guys!
-
I was going to jet my raptor 660 I was planning on running without a aibox lid. What do you recommend on the jet sizes. Another website said 155l 160r 25 pilot jets. I also have a stock exhaust. Will I notice any power difference if i jet my quad and run without a airbox lid.
-
I was going to buy a used carb that has been jetted for a certain exhaust. Since the carbs were jetted can I use them on a quad with a stock exhaust. I was planning on no airbox lid with stock exhaust until I get enough money to buy a full exhaust system.
-
Got it together last week. All powder coating was done by myself, with the exception of the swing arm and subframe. Barker built motor, +1 head, Cuervo cam, Sredrum throttle body, CP Tech piston, Troywcc EVAC valve Templeton drag pipes Skat Trak 76 rollout 12 paddle haulers Custom drilled rotor QuadTech foam/cover AM Chassis +6" "T" stem and -8 width +6 forward single arm rigid front end ASV C5 clutch lever Turbo Chassis +4 swing arm Direct Drive CNC 10x2" front wheels W2 (spindle mounts) Sandtoyz Unlimited 18x3 front tires Custom aluminum "bumper" Custom lightweight rear caliper Fly Racing start button ECATV tether Modified lightweight subframe Big thanks to Quality Powdercoat (qpcoat.com) for the subframe powder coating and swing arm coating, Brett (sand2kinc.com) for helping me out with some tips when putting together... And numerous members from other forums for helping me get the parts to build this. It weighed in at 312lbs wet with this 25lb axle, a 12lb aluminum JJ&A axle is enroute.
-
First of all I would like to thank you everyone in advance for there help. I picked up a 2004 Raptor 350 for $500. There is less then 50 hours on this machine. Its been sitting for most of its life. Its in pretty decent condition. I pulled the carb and cleaned it out. It was full of green corrosion. While I was doing this I notice that the throttle plate was sticking. I looked to see if parts were available separately and nope they were not. I found a 2006 raptor 350 carb on ebay for $65. I received it today and it was even more corroded then the original. So I took all the bowl internals and swapped them over to the 06 carb. I cleaned everything really good. I slapped it on the bike and it runs but its back firing when you give it gas, doesn't want to idle with no choke. I have to apply the choke perhaps 20~30% to keep it at an high idle so it won't die. My question is. Is the 06 carb compatible with 04? They look identical. My next move is to order a rebuild kit. Do I order one for 06 now? Are 04 through 08 the same?
-
Hi everyone I have a 2001 raptor 660 and I had it up to 75 mph and everyone says there is this speed limiter that won't let it go over 75 mph. I was wondering what you could do to make it go over 75 without different gearing or sprockets. Could you remove this limiter somehow. Thank You everything is stock besides the K and N airfilter
-
Hi everyone I have yamaha 2001 raptor 660 and I had it up to 75 mph and everyone says there is this speed limiter that won't let it go over 75 mph. I was wondering what you could do to make it go over 75 without different gearing or sprockets. Could you remove this limiter somehow. Thank You everything is stock besides the K and N
-
does anybody know if the meter on a newer raptor 700 will work on an 07 model. i know you half to change the hood out. but i mean like the tach/ speed/hour/time. cost on that meter is 266 so i dont want to buy it if it wont work..
-
I'm looking at buying my first sport quad, first yamaha, and first raptor. So of course I'm clueless on these. I have yet to see the quad in person as its a little over an hour drive from my house so I'm trying to get all the info I can before deciding if its worth the drive. It is a 2009 model and the SE. I was asking the guy about mileage and hours and he at the moment wasn't sure on hours but when we talked miles he said "It's still in kilometers, but I think there is right around 1000 miles on it. Not sure on hours right now." Why would it be in kilometers and is it hard to change it to show miles? I know in person condition is everything but if it has 1,000ish miles on it is $4500 to much for this quad? 2009 raptor 700r SE. So far all I know is "I have a 2009 Special Edition Raptor bought new in Summer/Fall of 2010. All stock except slip on exhaust and nerf bars. It has low miles and hours. It has honestly been babied, and oil changed and maintenanced very well. Still has original tires with decent tread. I'd like to have around $4500 for it, but will listen to reasonable offers, and then the kilometers guess at 1,000 miles."
-
Hey guys Im looking at buying a 2001 raptor 660 that has just had a new clutch, top end, tires, and it has a full fmf exhaust. This quad runs and drives but needs new plastics and seat cover. My main question is what is this quad worth, are the plastics from different years of the 660 interchangeable and what do I need to watch out for? Thanks in advance!!!