1997 Yamaha big bear 350 Shift shaft issue
-
Similar Forum Topics
-
By ResQ91
Hi guys
My 87 Bear 350 won't start and could use a hand.
Turn key on and Oil light turns on and then slowly fades out. (I think this is key to this) No start, not even a tick.
battery and connections good
A Solenoid post jump turns it over
Neutral Safety Switch wire attached and seems good
It has not had a wire/switch on Rear Brake Pedal ever since I had it.
Any thoughts on some other things to troubleshoot this??
-
By utvboard
2009 HONDA BIG RED
Honda enters the MUV (multi-use vehicle) market with a side-by-side machine that leapfrogs the competition to set new standards in utility and recreation. With numerous automotive-based technologies, Big Red features a powerful 675cc OHV liquid-cooled PGM-fuel-injected single-cylinder engine and an automatic transmission with three selectable drive modes plus Reverse, front and rear independent double-wishbone suspension, a roomy cab featuring rubber-mounted bucket seats with adjustable backs, and a specially designed, highly durable, tilting cargo bed. A broad selection of Honda Genuine Accessories will also be offered.
Big Red
KEY FEATURES
- Powerful OHV, liquid-cooled, PGM-fuel-injected 675cc, mid-engine design.
- Automatic transmission with Reverse.
2009 Honda Big Red in Camo
- Three selectable drive modes.
- Front and rear independent double-wishbone suspension for an impressively smooth comfortable ride.
- Roomy cab and rubber mounted bucket seats with adjustable backs designed to comfortably fit a wide range of body types and reduce fatigue on long drives.
Specially designed, high durability, tilting cargo bed
- Specially designed, high durability, tilting cargo bed.
- Wide variety of Honda Genuine Accessories.
- Summer 2008 release. More information to come soon!
Board Message - UTV Forum - Online UTV Community and UTV Forum
-
By John Sinclair
I WANTED TO UPGRADE THE CARBURATOR ON MY 1992 BIG BEAR 350, SO I ORDERED A NEW CARB FROM EBAY. ACCORDING TO THE WRITE-UP IT WAS A GOOD FIT FOR BIG BEARS FROM 1988 TO 1996. WHEN I REMOVED MY ORIGINAL CARB I NOTICED THAT IT WAS DIFFERENT FROM THE NEW CARB MY CARB HAD TWO THROTTLE CABLES THE NEW CARB ONLY HAD ONE CABLE. HOW CAN I MAKE THIS CARB WORK ON MY TWO CABLE THROTTLE? -
By McG75
1996 4x4 Timberwolf rearend width. Can someone with some knowledge of these machines answer this question for me please. Are all 4x4 timberwolves this narrow in the rearend? These tires are so close the right one actually rubs the muffler. Thinking about seeing if there are any spacers out there for it. I need at least an inch more clearance.
.
-
By ResQ91
Hi Guys!
New member and could really use your advice. I would have to believe this has been an issue for others but a search here came up with nothing......? (Probably me not doing search correctly)
I have an 87 Big Bear 350 YFM350FWT
The OEM Mikuni BTM carb is shot and would rather replace than rebuild.
It is no longer made and I have had good luck with NICHE carbs so I ordered a #K-CRB-0006 This was what they said was replacement when ordered. This Carb only uses 1 Throttle cable. The Slide is linked so it uses one. (OEM had 2nd cable coming through top to move slide)
Problem is when I ordered a replacement Cable from NICHE (#C-CBL-0061) the Cable wire is a little short, not allowing Throttle to return all the way down to Idle position. I called NICHE and they are at a loss. Haven't gotten back to me after 2+ weeks.
What would you recommend other than a carb rebuild?
Can I just use 1 of the OEM cables (It is the right length) and snip/disconnect the other that went to top of Carb for Slide?
Or ??
Thanks in advance for any advice you have!!
Dave
-
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.