Quantcast
Jump to content

Recommended Posts

Posted

I’m brand new to 4 wheelers and just bought a 1987 Yamaha Moto 4 350. It has good compression and fuel, but no spark. I’ve looked high and low trying to find how to test all the components of the ignition system, but can’t find anything. This has a new CDI box on it, but I suspect it might be the stator. How do I test the stator on this? Any help would be greatly appreciated! 

  • Admin changed the title to Need help! 1987 Yamaha Moto 4 350
Posted

I would probably check the pickup coil for proper resistance and that it is putting out voltage first, the value should be listed in your repair manual. If you dont have a manual you should try to get one. Is your new CDI aftermarket, sometimes they dont work right out of the box, if the original CDI is OEM dont throw it away until you are sure thats the problem.

  • Like 1
Posted

Yup. What Gw said, and check the resistances right at the cdi also to make sure the wires are intact. Check them down at the engine then again at the cdi and compare the figures..

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.



  • Similar Forum Topics

    • By WeeBee
      I'm looking at buying a New "CarryOn" 5'x8' Trailer with the Ramp Gate and Mesh Floor from my local Tractor Supply store ! Anyone have any experience with this Brand of trailer to share ?? Thanks!
    • By 88bigbear
      Bought a 88 big bear 350 4x4 took it for a run and lost spark, found it was stator so I replaced that then took it for a long run and it sat for 2 days and no spark again, this time stator tests good on ohms and voltage for source and pick up coils so I started replacing things including regulator, ignition, ignition coil and plug cap, spark plug and everything tests great including all safety switches until the orange wire for ignition coil from the cdi it only reads 3 volts so I replaced the cdi and still 3 volts, any ideas??
    • By cfherrman
      Fixing for a friend. Atv was at a different friends house to be fixed and he rebuilt the carb and had it running nice, then it shut off and no more. He replaced the key and the coil.
       
      So he got busy, so I am helping, I checked the wiring from the stator to the cdi, and from the cdi to the coil. All is good. I checked resistance on the pickup coil, good, and on the source coil, open. I buy a new stator (China) and the 4 prong plug only has 3 wires in it while mine has all 4. I checked resistance in the source coil and it's in the 300's. I pulled one of the old pickup wires out of the old stator and wire it in the new one. Still no spark.
       
      Why do the wires differ, I checked the VIN again and it's "J" for the year and I got a 1988 stator. Please help!
    • By LashinWheeler
      Hello all, I have a 2006 Polaris Sawtooth with no spark. It has a dead battery but with a jump pack on it, it will still not Spark. Plug is good, Throttle ETC is not closed, Stator pick up coil seems to Ohm out in the correct range, Unsure how to properly check the CDI. And when ignition is on the Neutral and reverse light come on but after cranking just the neutral stays on. 
       
      Any help would be great,
       
      Thanks!
    • By flyinbrian365
      View File 2023 Yamaha RMAX4 Wolverine 1000 service manual
      Factory service manual
      2023 Yamaha RMAX4 Wolverine service manual
      Submitter flyinbrian365 Submitted 06/08/2026 Category Yamaha UTV  
×
×
  • Create New...