Quantcast
Jump to content

Recommended Posts

Posted

OK, so I was riding my ATV and stuff..Recently I just installed a new Big Gun Rev Box thus making the RPMs rev higher and i Noticed that when i try to accelerate rapidly it really winds pretty high before going to a more normal tone.

So it starts well and you can find nuetral easily and all that stuff but when you go to shift into first or any gear for that matter; It just revs and the chain or anything will not move. I know its not stuck in Nuetral because the light goes off when you shift down but you still can't go anywhere.

Any Ideas?? I was thinking that the clutch is done possibly?

Think it could be the new Rev limiter that blew out the clutch or what?

Posted

Welcome to the site, I really don't see how the rev box would cause your tranny to go out. Maybe just bad luck. I would try taking the rev box out, put it back to how it was and try. If your quad runs fine without it, there's your answer. If it does the same thing you know you need to start digging in the tranny.

Posted

Hey, I don't think its the rev box or anything. My raptor is an 04' and its been raced and rode pretty hard. So i'm thinking that the clutch is just worn out which is causing it to slip. So i think i'm going to buy a new clutch. Does that sound about right?

Posted

Yeah, but I would still test it without the after market rev box. You never know what a faulty box could do. It would be a cheap fix if it is the box rather than replacing the clutch and seeing that it still does it. Eliminate the simple stuff.

Posted

replace the rev box with your oem box, see if that is the fix for the high rev u were talking about. as far as the clutch well id check and see if the plates are burnt and make sure everyhting clutch wise in good

Posted

Do any of the other gears Pull?? that sounds like the classic 660 tranny nightmare:confused: if its not your clutch, 3rd gear is the most common to drop first, but not all the time, especially if rode hard or raced. Good luck with that aspect. now the rev box is a different story, they not only extend the revs, but they also change the spark curve, if it doesnt sound right, then its probably not right, changes in timing could cause other existing issues to surface(leaky valves, piston slap) but also they could be more minor like air/fuel mix or octane deficiencies causing spark knock from the newer more progressive spark timing. Good luck with it! Keep us posted!

Posted
Do any of the other gears Pull?? that sounds like the classic 660 tranny nightmare:confused: if its not your clutch, 3rd gear is the most common to drop first, but not all the time, especially if rode hard or raced. Good luck with that aspect. now the rev box is a different story, they not only extend the revs, but they also change the spark curve, if it doesnt sound right, then its probably not right, changes in timing could cause other existing issues to surface(leaky valves, piston slap) but also they could be more minor like air/fuel mix or octane deficiencies causing spark knock from the newer more progressive spark timing. Good luck with it! Keep us posted!

lol the 660 has a joke for a transmission!

Posted

Well I just got back from dropping it off at the shop. So they're going to tear it apart and see what the problem is...So for the next two weeks i think i'm stuck on my pit bike : ) As soon as i hear from them i'll let you guys know.

Posted

you dont need a rev box on a 660 [is it a 660? no garage] you need a pipe and some jets. that's a torque engine, not a screamer.

clutch should not fail all at once without some weird noises or smells. Check the oil, I mean SMELL the oil. It will tell you.

Raptor trannies were only "bad" in 01, I have one I bought brand new, so does one son, no problems, and he services his after I badger him for 6 months to bring it here so I can do it! hahaha

Only 01 has different first and second gear ratios too, and no limiter on reverse [that can be scary].

Let's be specific about what you ride and then we can go from there OK?

Build your own page here buddy, so we can see what you have! It's fun!

:wink:

Posted

So i just got a call back from the shop..They said New clutch kit, Rear brake Disc, Calibration kit or something like that. and just about an hour and a half of labor for each part and with a grand total of.............................850$ dollars. I think i'm going to do the brakes myself but i'm not touching anything to do with the clutch. So i guess thats that, Unless anyone wants to come help me with my clutch : )

Posted

If you wanna load that up and drive it to Oregon, I'll be happy to help you- I have 2 raptors in the shop right now... and I'm sure I can beat the dealer's price.... let's see, Wisconsin to Oregon.....we need an excuse! Load it up and head for the Oregon Dunes, then stop by here on the way! that'll work. :wink:

Posted

Ill drive the 9 hrs to install your clutch and everything else!!!!!!!!!

What a RIP!!!!!!!!!!!!!!!!!

I hope you decide to do something different...Im frealkin Drunk right now and do what the shop would do!!!!!!!!!!!!!!!!!

Holy Crap.....Tje wofe os bi,mping me off the puter....!!!!!!!

Posted

Ha, Well i'm gonna order my own parts and just let them do the clutch only.. If my calculations are correct it should cut down the price to around 500-560 depending on how much the shop is going to charge me for labor. So its not too bad, but much better than 850 dollars. Also it takes them a week to get parts...what a joke; i can get mine in two days.

Posted
Ha, Well i'm gonna order my own parts and just let them do the clutch only.. If my calculations are correct it should cut down the price to around 500-560 depending on how much the shop is going to charge me for labor. So its not too bad, but much better than 850 dollars. Also it takes them a week to get parts...what a joke; i can get mine in two days.

a week????

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Forum Topics

    • By quadnut20
      23 friends 5 days great weather in Wyoming riding Sand Dunes & trails !!











    • By quadcrazy
      Mud riding is one of the most popular forms of ATV riding, but the wrong tires can leave you stuck fast in deep ruts and swampy trails. Choosing the best ATV tires for mud can dramatically improve traction, steering control, flotation, and overall off-road performance.
      Whether you ride trails, mud parks, swamps, or backwoods terrain, this guide covers some of the top ATV mud tires available today and what makes them stand out.
      What Makes a Good Mud ATV Tire?
      Mud tires are designed with aggressive tread patterns and deep lugs that help clean out thick mud while maintaining traction. The best mud tires usually feature:
      Deep tread lugs Wide spacing for self-cleaning Strong sidewalls Taller tire sizes for added clearance Durable construction for rough terrain 1. Maxxis Zilla

      The Maxxis Zilla is one of the most popular ATV mud tires because it balances mud performance with trail comfort. It is lightweight, aggressive, and performs well in a variety of terrain conditions.
      Why Riders Like It
      Excellent mud clean-out Lightweight design Smooth trail ride Available in many ATV sizes Best For: Trail riders who also spend time in mud.
      2. ITP Cryptid

      The ITP Cryptid is designed for serious mud riding with deep tread lugs and strong sidewall construction. It provides excellent traction in deep mud while remaining durable on rough trails.
      Features
      Deep aggressive tread 6-ply durability Strong side bite traction Great for lifted ATVs Best For: Deep mud and swamp riding.
      3. Outlaw 2 ATV Tires

      The Outlaw 2 has become a favorite among hardcore mud riders thanks to its massive lugs and impressive pulling power in thick mud.
      Pros
      Extreme mud traction Large tread design Excellent forward bite Popular in mud parks Cons
      Rougher ride on trails Heavier than trail-oriented tires Best For: Dedicated mud machines and mud bogs.
      4. STI Out & Back Max

      The STI Out & Back Max offers a solid balance between aggressive mud performance and everyday trail comfort.
      Highlights
      Durable sidewalls Great traction in loose terrain Smooth handling Long tread life Best For: Utility ATVs and hunting machines.
      5. SuperATV Assassinator

      The Assassinator is built for extreme mud riding and features huge paddle-style lugs capable of digging through the nastiest swamp conditions.
      Features
      Massive tread depths Extreme mud traction Available in oversized setups Designed for hardcore mud riders Best For: Extreme mud builds and dedicated swamp riders.
      Choosing the Right Mud Tire Size
      25-27 Inch Tires
      Great for stock ATVs Less drivetrain strain Better acceleration 28-30 Inch Tires
      Balanced performance More ground clearance Popular for trail mud riding 32+ Inch Tires
      Maximum mud performance Best for lifted ATVs Ideal for deep swamp riding Larger tires may require clutch upgrades, lift kits, or gear reductions depending on your ATV.
      Bias vs Radial Mud Tires
      Bias Ply Tires
      Stronger sidewalls Better puncture resistance Popular for aggressive mud riding Radial Tires
      Smoother ride quality Improved handling Better trail comfort Most serious mud riders prefer bias-ply tires because of their durability in harsh terrain.
      ATV Mud Tire Maintenance Tips
      Wash mud off after every ride Check tire pressure regularly Inspect sidewalls for damage Rotate tires periodically Avoid excessive pavement riding Lower tire pressure can improve mud traction, but beadlock wheels are recommended for very low PSI setups.
      Final Thoughts
      The best ATV tires for mud depend on your riding style and terrain conditions. Riders who split time between trails and mud often prefer versatile tires like the Maxxis Zilla, while hardcore mud riders typically choose aggressive options like the Outlaw 2 or Assassinator.
      Before upgrading to oversized mud tires, make sure your ATV can handle the added weight and drivetrain stress. Proper setup can dramatically improve your ATV’s performance in deep mud and swamp terrain.
      Visit QUADCRAZY ATV Forum for ATV tire reviews, mud riding discussions, builds, and technical advice from fellow riders.

      View full post
    • By BillR94
      I picked up this ATV that had no spark. The previous owner said he was driving it and it died and would not start. He discovered it had no spark. He replaced the CDI and the coil with no luck. He got tired of it and I bought it. I replaced the stater and now it has strong spark. Now, it starts for a second or two then dies. It will not stay running. I have checked the timing and it is spot on. The valves are adjusted correctly. I see no warn issues with the cam. I put the original CDI and coil back on it. Same problem exists. Compression is at 65 psi (has decompression mechanism),
      I took off the muffler in case the issue was clogged pipes. No change. I replaced the spark plug. No change. The carb was an aftermarket so I put a Niche carb on with no change. I bypassed the fuel pump and that did nothing to solve the problem. 
      I don't know if this is a carb issue or an ignition issue. I am looking around locally for an OEM carb to try out but not sure that will fix the problem. 
      Can anyone help me solve this problem. I am running out of ideas. 
      Thank you for your time
      Bill
       
    • By middlebrookgt
      I have replaced the cracked stator cover on my non-running 2006 LT-F400F that I purchased recently, checked all the shafts vs the service manual and pics and advice here.  I replaced missing gears, bushings and washers, made sure that truth marks were all aligned properly, that the shift cam springs felt like they returned properly, etc.  IAfter installing the new stator cover I checked the transfer lever for proper movement from L-H-R and then cranked it up.  Happily, it runs and changes gears well in L,  but it will not shift into H or R for anything.  I have opened it back up and am going back through it looking for the missing puzzle piece(s) but how can I best check that I have everything right this time before buttoning it back up?
    • By mikeexplorer
      I took this video back in 2007. Recently the trail (old railroad grade) I was riding was converted into a walking trail (obviously no more ATV riding on it) 👎 I dug up this old video and put it together since it shows the entire section and what it used to look like. The quality of the video is lacking, but this was from 18 years ago. Image stabilization didn't exist back then so I wore the camera on my helmet. (mounted to the quad was useless with all the shaking) so there is some annoying frames of me looking around. I noted any historical items from the railroad in the video. There is a section where the railroad grade is wiped out due to erosion so I had to jump off it and ride an abandoned road for a section to get around it. 
       
×
×
  • Create New...