Quantcast
Jump to content

Yamaha Raptor 660r Clutch Slipping

wrwiii12

By wrwiii12
in Yamaha ATV Forum

 Share

Recommended Posts

wrwiii12 Apprentice

wrwiii12

Posted
Posted

I have a raptor 660r and I have adjusted the clutch because initially my issue was that when I put it in reverse it would bogg down and die out because it acted like it was not all the way in gear. Then my reverse works after adjusting the cable by the engine and now I am noticing that when I give it alot of gas it slips and does not have all the torque. I also noticed this when I was pulling someone out it was slipping real bad. Anyone have any suggestions?

wrwiii12 Apprentice

wrwiii12

Posted
  • Author
Posted

Thats what I originally was adjusting to fix the reverse issue was the cable. As far as all that other stuff I guess I will have to go through the manual to see how to do all that stuff because I have never really played with transmission type of stuff before.

  • 3 weeks later...
Raptor8 Proficient

Raptor8

Posted
Posted

I think Dirt Demon has it. readjust the cable so it has a little more slack in it.

I recommend the Dr.D reverse lever for 660rs, it's COOL and makes reversing and adjusting really easy.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Popular Now

  • Similar Forum Topics

    • Joeguy
      91 quadrunner lt4wd shifting issue
      By Joeguy
      After i did my rebuild it seems to not want to shift well. I think the cable is alright, and when it does shift its nice and solid. I have to basically use my hand to shift and i have to pull or push it very far, like max travel, to get it to shift. I also tried adjusting the clutch set screw. Any ideas where to go next, or maybe i should just grab a new cable to try.
    • logray
      Looking for Quadrunner Flywheel Starter Clutch Gear race diameter
      By logray
      Hi all, 

      I am wondering if any of you have a Clutch Starter gear from a 1988 era quadrunner 250 sitting around that you could get me a precise measurement of the outer diameter of the race the sprag engages onto, for me? I need to machine a damaged race down and install a hardened sleeve and need that measurement (it's on a different gear than the OEM one, so I can't buy and use a OEM gear). 

    • OldATVowner
      99 Bear tracker no neutral or reverse light or start button
      By OldATVowner
      Just getting into this issue really. Been replacing solenoids but now I'd like to track down the problem. This time I'm not getting neutral/reverse lights or start button. Was on a creek ride when it started doing this recently. It cranks by arcing the solenoid and gives me no light or start button but if I crank with the pull cord....the neutral light and the button work. Turn it off and try to crank with the key and nothing. I'm looking into the safety switch issue tomorrow and re charging the battery. Just figured this was odd enough of a problem that you guys might be familiar. Thanks
    • Dsluder
      Fuel issue
      By Dsluder
      I am having an issue with a hs500. I bought it broken and have been trying to get it running. It seems to be starving for fuel. If I put my hand over the intake it will crank but will not run for very long because I'm not able to get the correct airflow with my hand. The things I have done so far are. Replaced the fuel pump, fuel filter, mass airflow sensor, idle air adjuster, fuel injector, cleaned the throttle body, replaced the ecu, and still the same issue. I notice the injector does not spray when removed from the head. I dont know if that is common. 
       
      I am out of ideas on what to do next. I have removed the fuel line from the injector and it is getting plenty of fuel. If anyone has an idea on what could possibly be the issue I would be happy to try anything at this point.
    • hengstserepair
      2000 Yamaha Breeze 125 slips in Forwards, runs fine in reverse
      By hengstserepair
      Howdy ya'll. I am working ona 2000 Yamaha Breeze 125. It was in rought shape when I received it and I am working through issues as they pop up. The quad had been sitting for years. I was able to get her running again, but I need your help with the following issue:
      I don't trust the transmission yet and I don't want to make problems any worse. So, I haven't pushed things hard at all. Low rpms, less than 5mph in reverse.

      Nuetral: Runs as expected
      Reverse: She seems to be driving fine at slow speeds. Going into reverse at idle is fine, coming out of reverse back into neutral won't work (the shifter is just stuck). As soon as I turn off the quad, I am able to shift around without any issue.
      Forward: It slips. It seems to only transfer power to the wheels on a smooth surface and going slightly downhill. When shifting into forward at idle, there is a clacking sounds during the transition. Shifting back to nuetral works just fine.

      Other Notable Symptoms: There was old oil in the vbelt and when I was tuning the carb, it starting blowing out of the CVT cooling vent at the front of the quad. Made quite a mess. There is positive crankcase pressure due to piston blowby, that I have not decided whether or not I am going to fix (customer budget dependant).  Since the oil was old, much darker than the new oil that is in the crankcase, I am thinking it seeped past a bad seal while it was sitting for years. The oil that was in it when I first got it had gas in it.

      Thoughts: I am thinking maybe there is an issue with the clutch. I worry about the old oil intermingling with the dry centrifugal clutch. I was thinking my next step would be to take the cover off of the clutch and inspect it.

      Let me know what you all think. Any advice and ideas is greatly appreciated. This is only the 3rd quad I have worked on and I have a lot to learn.

      Lorne

COMMUNITY SECTIONS

ATV FORUMS

QUADCRAZY MEMBERSHIP

Be a part of best online community of ATV riders and join thousands of people who love ATVs! Share your ATV photos, videos, ATV rides, get help with your ATV and more. Not a member?

SIGN UP TODAY

ADVERTISE WITH US

FOLLOW US ON

  • Automotive Webmaster
×
×
  • Create New...