6 posts in this topic
I hope this is right form is not point me the right place.
I have just brought a 07 king quad 700. Its got 14 rims with 28 tires. Can't remember what brand right now.
What I would like is a programmer and a clutch kit for it. I'm used to diesel trucks really new to the fuel injected quads.
Let me know what my bike needs thanks.
I have a 1997 Honda fourtrax 300. It runs great but, I almost got stuck in the mud this weekend so, I am now thinking about mud tires and some minor mods. What do you guys suggest for some minor modifications to get some better performance? It performs pretty good but, sometimes when driving pretty hard, the clutch slips a little. I am also thinking about a lift kit. Which one would yall recommend?
Been busy the last little while finishing a bathroom for the wife while the dealer did some work on my Can-Am. Before you say, "What the hell did ya take it to the dealer for ??" ...... let me finish my "What Have YOU Done for Your ATV Today ??" report .......
When I took the tracks off, I noticed both the front and the rear diff seals were leaking and there a pin hole in the front inner CV boot down inside one of the boot creases ... so, after talking to the dealer (who BTW, seems to ALWAYS treat me right) said he could have it all fixed in a couple hours once he had the parts in hand. So I took it in and first, he ordered two diff seals right ?? ... Well BRP in their infinite wisdom, thought that must be a mistake & only sent ONE seal .... so after the other seal comes in they start the work and when the pull the front axle to change that boot .... the CV joint fell apart !! They said they had never seen that before, there was plenty of grease in the boot, so ... ?? ..... Anyway, they ordered a new one .... under warranty !! ........ Now is THAT cool or what !!?? .... So I wait a few more days to get my bike fixed ... and in the mean time, I had been ordering stuff !!
First, I bought several 15 ft rolls of the DEI Titanium Header Wrap and Re-Double-Wrapped my header pipes. The old DEI header wrap was 2yrs old & it just kinda fell apart and came off in pieces and some had just burnt away too.
Next, I had heard about a "High Performance Water Pump Impeller" for the Can-Am's but I could NOT find out where to buy one. After about a year of searching, I found out they're made in Czechoslovakia. I contacted the guy but he didn't want to send just one because he said shipping would be expensive. Then I found a guy who has been making frames for that guy & said he would order a batch next time he did a shipment ... but I have no idea when that would be. So, asking around again and making some more phone calls, I found a performance shop in Canada that had some ... it was a lot more ... but I ordered one anyway. This impeller is suppose to move 40% more water. And you might ask, "Did I Really Need It ??" ....... and my reply is, "What a silly question !!"
After taking the stock plastic one out, I noticed some of the vanes look pretty beat up. Not sure if that's the way it was new, or if the heat was breaking it down ??
While my bike was down, I spent some time talking with my dealer about suspension and shocks. I told him I really wanted to get some Elka's, but didn't want to spend a ton of cash. He told me he was a dealer for Fox shocks already and he would call Elka to see what it would take to become an Elka shock dealer as well. So, two days later, he gives me a call and told me was now a dealer for Elka shocks and that he would give me a good deal if I wanted to order a set. So I make a mad dash down to the dealer & order a set of Stage 2+R's. And boy, did he give me a GREAT deal !!
And with these shocks I knew the Rubberdown Lift I had wouldn't work (at the rear anyway), so I ordered a Highlifter Lift Kit.
After all that work, I greased it, changed the tranny and engine oil & filter. Now all I have left to do is install the skid plates, gas her up ........ AND GO FOR A RIDE !! :partyc: