Quantcast
Jump to content

Recommended Posts

Posted

I have a late 90's Bayou 300 I use for hunting rig here in Bavaria Germany(I am stationed at the US base here). It starts and runs fine(great in fact), I can take off ride for 10,20,30 minutes, then it will just die(time is not the factor). It will restart fine, run for a second and die again, and again, then it will be fine for 10 or 20 or 30 minutes. Temperture not the issue, warm weather or cold doesnt matter. elevation not the issue, hills or flat not the issue. I removed tank, completely cleaned(yes some dirt in bottom. replace inline filter, carb seems good. It still feels like it is starving for gas when this happens, not an ignition issue. Do I need to pull tank again? pull carb and clean again?

Thanks,

Jack in Grafenwohr Germany

Posted

Welcome to QUADCRAZY! Always glad to see people form overseas and especially our military!!!

Sounds like fuel starvation to me and possible an issue with your carb and float level or pin issue, where the bowl runs dry and does not fill up in time. Have you taken apart the carb?

Posted

I agree with Ajmboy, if it is a fuel issue, something hanging the float up seems really likely. There could be a tiny piece of debris catching the float plunger and keeping it from dropping, or it may just be a bit worn and sticking in the seat. I would start by taking the carb apart and do a good cleaning on EVERYTHING make sure to clean out all the jets, fuel passages and vent holes. Also, make sure every thing is bolted up tight when you put it back together, if you are sucking air in from anywhere, it can affect the fuel uptake in the carb and cause a lean condition too which is bad. If none of that seems to help, you may be looking at a possible ignition problem.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Popular Now

  • Similar Forum Topics

    • By marlon smith
      1990 kawasaki bayou 300c idles fine but pops out exhaust and intake when trying to excel, will not take throttle past 1/4 , any one had this problem?
      have replaced carb twice, same thing, fresh built engine cylinder head, same as before, new spark plug, flywheel key is good, pulser test good, good spark
    • By dkgg5755
      This thing came with a cheap aftermarket carb on it the problem I'm having is it won't start with choke installed into carburetor it will start and get run without it installed then bogs out after about 2 min run time I've checked timing , compression, checked valves for proper clearance , also did a smoke test for air leaks found none. 
    • Guest
      By Guest
      Hey all, new to the forum! I just bought a 1998 Kawasaki bayou 300, 4x4 not running. Initially I found no spark. Ended up playing with the plug wire (made sure plug top and wiring was touching) and got spark yesterday and the quad fired up off ether. Come to work on it today and now no spark again. Before I got spark and now today if I touch the plug after cranking I get shocked, and it will spark after I release the starter button. I was jumping the quad with a freshly charged car battery that has 12v while cranking. Cleaned out the kill switch and ignition button. All looks good. Purchased new plugs. They're are a lot of wires cut/ disconnected. But shouldn't matter if I got spark without them connected... 
    • By BillR94
      I picked up this ATV that had no spark. The previous owner said he was driving it and it died and would not start. He discovered it had no spark. He replaced the CDI and the coil with no luck. He got tired of it and I bought it. I replaced the stater and now it has strong spark. Now, it starts for a second or two then dies. It will not stay running. I have checked the timing and it is spot on. The valves are adjusted correctly. I see no warn issues with the cam. I put the original CDI and coil back on it. Same problem exists. Compression is at 65 psi (has decompression mechanism),
      I took off the muffler in case the issue was clogged pipes. No change. I replaced the spark plug. No change. The carb was an aftermarket so I put a Niche carb on with no change. I bypassed the fuel pump and that did nothing to solve the problem. 
      I don't know if this is a carb issue or an ignition issue. I am looking around locally for an OEM carb to try out but not sure that will fix the problem. 
      Can anyone help me solve this problem. I am running out of ideas. 
      Thank you for your time
      Bill
       
    • By T37Mark
      HI everyone. New to this forum. I have 98 Kawasaki Bayou 400 with an apparent electrical issue. I have the Clymer manual, but I am not exactly sure where to start. The issue started a month ago and the neutral light would go on and off intermittently. Eventually it went completely off , and I thought it was a shifting issue. I took the case off and checked the clutch and all mechanical shifting components are good, so I think I eliminated that. The switch sometimes works, sometimes doesn't. Last time I tried, I did hear a clicking sound near where the battery is right before the light went out. Does anyone have any ideas where to start? Hoping this is an easy fix.
×
×
  • Create New...