Quantcast
Jump to content

2006 Artic Cat 700 won't run.

orgdoaner

By orgdoaner
in Arctic Cat ATV Forum

 Share

Recommended Posts

orgdoaner Newbie

orgdoaner

Posted
Posted

my 06 700 cat just quit on me an all it does is try to start but wont run i dont have spark plug looks like rectifier but it throws fire an injector has fuel shooting out but if i pour gas into throttle body she runs till gas is all burnt up i am lost

DirtDemon Veteran

DirtDemon

Posted
Posted

This is a new topic so I started a new thread. It is hard to make out exactly what you are saying there. Try using a few more words and describe the problem in a little more detail please.

orgdoaner Newbie

orgdoaner

Posted
  • Author
Posted

ok i was riding an she just quit running tried to start the cat again an all it does is barely fire off then die cannot keep it running i pulled fuel line an fuel pump squirts gas everywhere i pulled injector and it sprays fuel out i have fire from spark plug if i pour gas down into throttle body it will run till all the fuel i poured in is burnt will not keep running just off of poured fuel or starting fluid has drove me crazy makes no sense got fuel got spark but wont run

orgdoaner Newbie

orgdoaner

Posted
  • Author
Posted

ok gas is full tank of new gas while sitting it was almost empty new gas has seafoam added to it just trying to run it thru make sure not dirty i know it will run with intake cover off i have done that tired of putting all back together to see if she will start the bike has no plastic now intake box is on just cover wit the 2 wingnuts is off it will not idle unless i pour some gas or startin fluid in throttle body but injector is sprayin fuel fuel pump is workin but after trying to start for a while efi comes on the screen display it does not come on every time i try an start so this is why i am so lost i got fire i got fuel but no starting an was running great an no after market exhaust just clutch kit an snorkel but had both from the begining an had her almost 3 years no problems tried on off switch just toggled it but if i turn it off it does what supposed to i turn it on i here the clicking sound an fuel pump running havent tried to disconnect battery but put new one on before al this started

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Forum Topics

    • docdoug72
      Has anyone had a suzuki 230 quad lock the engine up?
      By docdoug72
      Has anyone had a suzuki 230 quad lock the engine up?  Its a well maintained bike, it locked up when my son was riding it. Pulled the plug, it has connected with the piston. I'm thinking the con rod let go.  I don't have a service manual.  Does the engine need to come out to check further?
    • RGS
      1989 Moto 4 YFM350ERW intermittent spark.
      By RGS
      1989 Moto 4 YFM350ERW intermittent spark.
      Quad has set for about 7 years and was running when parked.  When I replaced the battery and attempted to start it had no spark. 
       
      What I have done.  Followed troubleshooting in the manual. 
      1.       Coil failed the resistance check so I replaced it.  Still no spark.
      2.       I performed resistance checks on the stator and they all pass.
      3.       Found a bad rear brake stop switch and unplugged it and connected the wires in order to disable.  Now I have intermittent spark.  I believe that the issue is with either the stator or CDI and not sure which.
      1989 seems to be a transition year for electrical.  I can get new aftermarket CDI units for 87-88 and 90-94.  I cannot get ones for a 89.  I can get new stators for 87-89 and 90-95.  Looking at the schematics the wiring on my moto is closer to the 90 ones on the ATV side of the CDI and closer to the 87-88 on the stator side of the CDI.  Looking at part supply sources the stator housing is the same part # for all the years and looking at some of the stators on Amazon that have the dimensions on them both of the stators are the same size.
      What I am thinking of doing is to replace the stator and CDI with a 90-95 one as these parts are all readily available.   Does anyone know if this has been tried before and if there are any issues with doing this.  
       As a side note I also have a 1993 Moto 4 YFM350ER that has been sitting longer but it is located about 400 miles from me at this time.  By doing this change in addition to being able to get parts I will also have 2 ATV’s that are the same electrically. 
    • Randel1
      Oxidized or faded plastic body parts
      By Randel1
      I recently read an article about restoring or at least improving the looks of faded and discolored plastic body parts. In the article it suggested using a 50/50 mixture of boiled linseed oil and paint thinner. You mix it up and apply it with a brush or rag to rub it in and remove the oxidation. I curious to find out if anyone has had experience with doing this and what was their short/long term results of doing so. I would hate to try it and find out that a few weeks/months down the road my plastic body parts self destruct.   
    • RadRob
      Hello to all.
      By RadRob
      I am new to this site. I have a 1987 Suzuki LT230S Quadsport I think. Is there a difference between quadsport and quadrunner?
    • kawasig
      I just bought a rare beast!
      By kawasig
      Hello All
      I'm kinda new to ATVs. I just bought a 1987 Suzuki quad runner 230 Dual Range. I'm having a problem finding info on it. It's very clean, only 2.800 miles. The front wheels are only 30 in.center to center. I was thinking about adding wheel spacers to give it more stability. I realize the added stress on ball joints and bearings. I'm wondering if there are any other concerns? Any input is greatly appreciated!

COMMUNITY SECTIONS

ATV FORUMS

QUADCRAZY MEMBERSHIP

Be a part of best online community of ATV riders and join thousands of people who love ATVs! Share your ATV photos, videos, ATV rides, get help with your ATV and more. Not a member?

SIGN UP TODAY

ADVERTISE WITH US

FOLLOW US ON

  • Automotive Webmaster
×
×
  • Create New...