Quantcast
Jump to content


83 Honda ATC 185S HELP PLZ!


Recommended Posts

ok guys i have a little problem with my 185s i have tried beating and heating the rear brake drum but it just wont come off any ideas am i missing something here? ive got the outter plate off the one with 6 bolts and that slides right off now the problem i have is with the inner plate it has holes in it but i cant see anything holding it on can some one plz help me i like my trike and would hate to get rid of it just cuz i cant fix my little problem

Link to comment
Share on other sites

you're getting smoke because there is a bearing in there- be sure and repack that with grease before reassembly.

I went out and got my 185 factory book. The drum is splined, of course, but after you remove everything between it and the tire, there's nothing holding it in there...

the backing plate and inner dust cover are welded to the bearing carrier, so that will be staying where it is.

Typical Honda manual, it says 'remove the brake drum.' hahaha perhaps a chilton's would be more enlightening...

I also haver a clymer's here tho I prefer chilton's. clymer= British, chilton= American

the language is different...

If you have both axle nuts and the washer removed, and the brake cables are slack, then there is nothing but corrosion holding that drum on there. Brake shoes sometimes wear out and then eat a groove into the drum.... a couple good smacks with a hammer should break them loose.

But other than that, it's heat I'm afraid. I have a clymers and a factory manual on that rig if you need any more help. [i have a 185 and a 200s]

Don't be afraid to ask.

I can fax you a picture if you have a fax machine or scan a page and email it to you. Let me know if I can help.

Start shooting those splines with PB Blaster or some other penetraing fluid....the splines are all that hold the drum on if you have the axle nuts removed...

Edited by Raptor8
grammar
Link to comment
Share on other sites

I have an axle in my garage right now, that has a drum that I believe has been heat welded to the axle. I even tried building a puller that grips the drum through the holes and used a hydraulic bottle jack to apply the pressure, one of the fingers on the puller just broke a piece off the drum. Unfortunately, the only way the axle comes out on this thing, is by removing the drum and pulling it out the other side. We have to cut the brake drum off and try not to damage the splines in the process, a new drum is going to run $130. At least you have a choice to take it out the other way if you can't get the it to pull off the splines.

BTW, I edited your posts for you, please try to avoid f-bombs in the future, I know you are probably frustrated, but this is an all ages forum, so please, atleast try to avoid actually spelling out the cuss words. Good luck with the drum, I hope you get it off there ok.

Edited by DirtDemon
Link to comment
Share on other sites

keep looking.... check the 3 wheeler forum here and look at some of MWKE's posts, the first few. he has some contacts there for 3 wheeler sites. SOMEBODY has one laying in their garage, bet on it! it's a treasure hunt man! hahaha have fun

maybe you can run a die down those threads and restore them. may require some hand filing.... it's a pain in the butt but I have done it before on a crankshaft and it worked. Next time screw the nut back on and pound on a wood block OK?

I'll look around too. Be sure and put it in the classifieds here- someone may have one!

Edited by Raptor8
Link to comment
Share on other sites

  • 2 weeks later...

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Forum Topics

    • By semicolon
      Hi, I am having issues with my TRX350D fuel pump.  It suddenly stopped running so I have replaced all the fuses and cleaned all the terminals.  I have fitted a new pump, fuel cut-off relay and rectifier.  Still nothing!!  The pump runs when attached to a battery.  The engine will start on the choke and the filter fills with fuel but it will  not rev and dies when the choke is closed. I have power to the relay but nothing at the pump black/white wire when cranking the engine.  Any ideas where to go from here would be very much appreciated!!
       
    • By NZrider
      My king quad 700 runs rough when cold then won't start some times but not often when it's hot. And occasionally smoke's a lot when it's cold I'm guessing that's rings but I'm worried unless it's causing the other problems
       
       
       
      All help is appreciated thanks
    • By bighoss
      i got my son new outlaw 50 a few weeks ago and we went rideing yesterday and while we were riding it died and it took me like 10 min to get started back and it died agen when we got close to truck so i pulled it back took the plug out it looked like it was drop in a bucket of gas took the air filter out and the ait box was full of gas also got home it started rite up today i started it it starter up but was blowing what look like water out of the exholst let it idel for a lil bit did not die but as soon as hit the gas and let off it will die what does that sound like i thnk i going to take it back to dealer and tell them to fix it as it is under warrenty but would like to know what it could be first
    • By N00bie
      From Arkansas. Just bought a 2012 Gator 850i RSX because I could not pass up the price. BUT it has an idle problem. So, to be honest, I joined just to get a service manual. I have a choice: 1)Buy a hard copy: ~$100; 2)Buy a CD ~$35.00; Get a direct download for free posting 10 times; or get a download for $29.00 (subscription). Haven't decided what to do yet.
    • By McG75
      Sorry I suck at these forums so if you see this submitted under update status, my bad. Anyhow this is a new shock for a 96 Yamaha Kodiak 400 4x4 it fits my 96 Yamaha Timberwolf 250 4x4 perfectly. Little narrower are the bottom than the original but everything else is perfect. I extended it to almost a half in from full extension because I’m pushing 350 pounds.  It rides and hold me well. So if any of y'allRace driven shock. have been looking for one and didn’t want to do the research here it is. 





×
×
  • Create New...