Quantcast
Jump to content

Suzuki LTR 450 Fuel Flush

pokerdad911

By pokerdad911
in Suzuki ATV Forum

 Share

Recommended Posts

pokerdad911 Apprentice

pokerdad911

Posted
Posted

I finally got my 450 started. It had been sitting for awhile, so the fuel varnished and now I have an OILY substance gunkin up my bike. I emptied my tank first before running it. Got out as much as I could. I got a compressor and blew it out from tank, took off fuel line before it goes into pump and injectors and flushed good new gas threw it TO FLUSH MY SYSTEM TO HELP CLEAN LINE,PUMP AND INJECTORS, VALVES ECT... It is sputtering and most cases wont stay on. HELP! Need advice before i junk it. wHAT ELSE CAN i DO. RUNNIN LIKE CRAP!

quadnut20 Grand Master

quadnut20

Posted
Posted (edited)
4 months. Is the injector gonna be gunked up or valves. It started but sounded strong but still would not idle on its own, poppin and burning like a 2 stroke.

If its burning like a 2 stroke something is not right !! I`m not sure about EFI systems but on a carb setup you have to throughly clean it Before you start it

Edited by Ajmboy

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Popular Now

  • Similar Forum Topics

    • middlebrookgt
      2006 LT-F400F stator/generator cover change: What is the best way to check that all is good with the transfer operation before reassembling?
      By middlebrookgt
      I have replaced the cracked stator cover on my non-running 2006 LT-F400F that I purchased recently, checked all the shafts vs the service manual and pics and advice here.  I replaced missing gears, bushings and washers, made sure that truth marks were all aligned properly, that the shift cam springs felt like they returned properly, etc.  IAfter installing the new stator cover I checked the transfer lever for proper movement from L-H-R and then cranked it up.  Happily, it runs and changes gears well in L,  but it will not shift into H or R for anything.  I have opened it back up and am going back through it looking for the missing puzzle piece(s) but how can I best check that I have everything right this time before buttoning it back up?
    • AnthonyT
      First time ATV buyer
      By AnthonyT
      In search of my first ATV? What are good older 4x4 models?
    • Frank Angerano
      My first trailer project.
      By Frank Angerano
      So I decided to pick up a small trailer if I could get one for the right price.  I found this one for a few hundred bucks on Craig’s list.  It is  a galvanized trailer which is exactly what I was looking for. The wood was shot and needed some minor repairs which I could care less about as long as the chassis was good. 
      I striped it down and put a new deck on. I had some vinyl realtree graphics that I had laying around so I added them to the fenders which I think worked out well. Very happy with this little guy.  
      I'm having the iron workers at my jobmake me up a few lightweight side rails that will have a 22 degree bend in them to accommodate the tires that slightly hang over the edge and will incorporate some tie down points as well. 








    • PupATV
      Help! Polaris 2001 325 Magnum Not Running
      By PupATV
      Hey guys! I am new here to the forum and need some help getting my Polaris 325 Magnum 2001 Running.....So I got it for free and it has never run quite right...I put a aftermarket carb on it last year and it was running fine but it only went like 20 maybe 25mph max......But then the needle and seat sealed leaked within a yeah and it flooded it REALLY bad so I changed the oil because it was full of gas. So then I put a genuine Polaris carb on it and I have it set to all the factory specs, but it was still not running right....So I replaced the ignition coil and the spark plug and that solved one of the problems I had (It would bog down and stop running when i would go up a hill) But it still didn't have that much "Punch" to it like my Kawasaki Prairie 300 ans Suzuki Kingkuad 300.....So I replaced the CDI but it's still not running right! It's acting like it rich kinda....So it runs mostly okayish when I have the airfilter on but the top of the airbox off but as soon as I put the airbox lid on it like REALLY bogs down and wants to stall really bad. I have the carb at the factory specs and it has a pretty new fuel pump so I have no ideas whats going wrong! It still nly has a top speed of only about 30-35mph and it sounds like it's choking the whole time! Thank you for sticking to the end, and I hope you guys can help me!
      -PupATV
    • bhristianzx12
      1992 Polaris 350L 4X4 Not Running
      By bhristianzx12
      I have acquired a free 92 Polaris 350L 4X4. Ive replaced carburetor from ebay, replaced spark plug, im trying to pull start but sounds like it doesnt want to fire. Spark is a bright orange spark (checked with spark plug tester), replaced plug, pre mixed gas from an external gravity feed tank. Compression test good. Anyone got any recommendations for me?

COMMUNITY SECTIONS

ATV FORUMS

QUADCRAZY MEMBERSHIP

Be a part of best online community of ATV riders and join thousands of people who love ATVs! Share your ATV photos, videos, ATV rides, get help with your ATV and more. Not a member?

SIGN UP TODAY

ADVERTISE WITH US

FOLLOW US ON

  • Automotive Webmaster
×
×
  • Create New...