Quantcast
Jump to content

Asking For Technical Help

yamaman

By yamaman
in Website How To & Feedback

 Share

Recommended Posts

yamaman Contributor

yamaman

Posted
Posted

when you are asking for help. give model ,year, size. also give brief history. saying i have a 350 and it wont start is not the way to ask for help. everybody has to ask all sort's of questions to find out after 10- 15 reply's that the bike sat for 8 month's with old gas in it.

say i have a 2008 Yamaha 350 and the machine has been sitting for a while and won't start.

or bike has no power. went in some deep water before this started happening.

Admin

Admin

Posted
Posted

Thank you Yamaman. I could not have said it better. we have been advocating for a long time and also have a requirement in our manufacturer forum to add the full year, make, model, and issue when posting.

I am going to Sticky this Thread! Moving to Member Feedback Forum.

  • 2 years later...
  • 3 years later...
Admin

Admin

Posted
Posted

Bumping this topic. It's very important to give full information is you are asking for technical assistance with your ATV from members in this community. Please also make sure that you post in the branded forums.

Thank you.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Forum Topics

    • RadRob
      Hello to all.
      By RadRob
      I am new to this site. I have a 1987 Suzuki LT230S Quadsport I think. Is there a difference between quadsport and quadrunner?
    • Tinkeringreg
      Kodiac no start project
      By Tinkeringreg
      Hi my name is Greg and I just acquired a free 2000 yamaha kodiac 400 4x4 with the ultramatic transmission that does not run. I plan to get it going and use it around my property

    • Kaz
      1999 Yamaha Big Bear 350 4x4 no spark
      By Kaz
      Troubleshooting a no spark issue, was running OK, maybe a little rich, turned it off, now no spark. I've checked/ohmed out the main key switch, the start/stop switch, neutral switch, brake switch - all good. It will crank the starter, but no spark with the starter or when I try the pull start. I've checked all fuses and diodes. Swapped battery. New plug. New coil. Swapped in a used CDI - no help. Traced, removed, cleaned, reattached all grounds. Removed things like my winch from the circuits to be sure a bad relay or something was dragging it down. When testing voltages, the orange wire going from the CDI to the ignition coil shows no/very low voltage-shouldn't it have 12V on it? Sometimes I get a very weak, intermittent glow on my spark tester, but not enough to fire the plug. I've checked continuity on just about all wires in the harness. Checked/cleaned/lubed w dielectric grease- all connections, redid a few that looked old/dirty. I've checked the stator resistances, all good, but have a stator and rectifier ordered anyway, will arrive Sunday. I verified that the rectifier has a voltage output back to charge the battery while cranking - 10.5-11V, low, but expected while starter is engaged. What else can I check as part of troubleshooting? I have a Haines service manual, but the 1999 350 4x4 seems to be an odd model, there isn't an exact electrical diagram for it, but found one for another year that has all the same number of wires and same color wires, so I've referenced that. Any hints, tips or advice would be appreciated! Thanks!
    • P_syko
      Need help! 1987 Yamaha Moto 4 350
      By P_syko
      I’m brand new to 4 wheelers and just bought a 1987 Yamaha Moto 4 350. It has good compression and fuel, but no spark. I’ve looked high and low trying to find how to test all the components of the ignition system, but can’t find anything. This has a new CDI box on it, but I suspect it might be the stator. How do I test the stator on this? Any help would be greatly appreciated! 
    • carkivey3
      2008 kazuma 800 4x4. i need wiring help. no spark
      By carkivey3
      i just picked this up. was told ran fine but overheating issues led to replacing head gasket and head. has not ran since. he is not a mechanic but helped someone else who he could not get back to finish job, got aggravated and put up for sale. i was thinking timing issues. i have 110-120psi on all 3 cylinders so i think valves are correct. dont know about distributor yet. however i have no spark. i have no power going to ignition coil. tried to follow white wire but gets lost in wire harness. does anyone have a wiring diagram? can anyone tell me what conditions have to be met before starting. motor turns over so i would think all safeties are met but you never know.

COMMUNITY SECTIONS

ATV FORUMS

QUADCRAZY MEMBERSHIP

Be a part of best online community of ATV riders and join thousands of people who love ATVs! Share your ATV photos, videos, ATV rides, get help with your ATV and more. Not a member?

SIGN UP TODAY

ADVERTISE WITH US

FOLLOW US ON

  • Automotive Webmaster
×
×
  • Create New...