Quantcast
Jump to content


1987 Kawasaki Bayou 300 Problem


fzeller

Recommended Posts

I don't feel I can help. But a few things for others who might be able too. Is the air filter clean, fuel filter, good gas, how does the spark plug look. Is it popping back thru the carb or backfiring out the exhuast. hard to start or easy to start any flooding. Has it been sitting up for awhile with old gas in it if yes have the carbs been cleaned.

Link to comment
Share on other sites

Hi again, No poping back through the carb. The gas is good, I have been riding it all along. It just started acting up when I started it last week. I ride it about twice a week, sometimes more. It starts great, it idles great, it runs great up to about one third throttle. As soon as I hit one third throttle it quits and I have to let off and it runs great again. It does not matter if I go up slow with the throttle or fast. When it gets to that point it quits. As soon as I let off it runs great again.

Link to comment
Share on other sites

check your fuel lines too. My daughters two stroke 90 would die when u try to give it throttle the air fuel mixture was out of adjustment. It would idle and soon as you hit the throttle it act like it ran out of gas. if you were to have a small hole or crack in the fuel line it will effect fuel supply.The ethanol in gas can cause line damage on small engines. If you were to find this to be the trouble you can buy ethanol shield from a store like walmart. I run it in my quad & lawn equipment. I know ethanol is the cause for my chainsaw, weedeater & hedge trimmers the repair shop said ethanol was what damaged the fuel lines. I don't know if it effects fuel lines on quads I just use it to be safe.

Link to comment
Share on other sites

First thing I would do is put a new spark plug in it and take note of what the old one looks like. The condition of your plug can give you clues as to what your problem may be. I am leaning toward an ignition problem since the problem started suddenly and you haven't let the machine sit for a long period. But I still would not rule out a carb problem, you may have a clogged jet, or or a stuck float or something.

Link to comment
Share on other sites

O.K. Guys. I just got in the house from working on it. I took the carb. off and cleaned it. I also replaced the fuel line and filter. I put it back together and she runs like a champ again.

I don't know exactly what the problem was, but you guys sure had it narrowed down for me. thank you so much for the help. Fredz

Link to comment
Share on other sites

Great to hear you got it running again!! Now have some fun. Did you look at the plug and check it's condition. Sometimes with a fuel or carb problem it can effect the plug and there cheap to replace just for the peace of mind if your out on the trail. Just keep one handy if you need it.

Edited by hangingon
Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Forum Topics

    • By ResQ91
      Hi guys
      My 87 Bear 350 won't start and could use a hand.
      Turn key on and Oil light turns on and then slowly fades out. (I think this is key to this) No start, not even a tick.
      battery and connections good
      A Solenoid post jump turns it over
      Neutral Safety Switch wire attached and seems good
      It has not had a wire/switch on Rear Brake Pedal ever since I had it.
      Any thoughts on some other things to troubleshoot this??
    • By hardcastle
      My friends KQ 300 starts fine and runs, as soon as you put it in gear and try to accelerate its bucks and farts like crazy, not moving... I cleaned carb and it worked good for 1 day... now back to same problem.... could it be such as a bent valve????
    • By cavry
      Wiring shows White and Brown to solenoid blades. Then a black wire from starter circuit relay to solenoid. I am confused,  where is that black wire supposed to connect?
      Thanks for any help
      Cavry
    • By Clydaho
      2022 Sector 550, 414 miles on it and the gas gauge reads empty.  I topped off the gas and it didn't change.
      There is no fuse that I could find.  No access at the gauge cluster.
      Wiring on the top of the tank looks good, properly connected.
      Could the sending unit in the tank be stuck or broken?
      Has anybody removed the tank lid?  Any tricks?  
      Any other ideas?
      Thanks for any help,
      Clyde
    • By ResQ91
      Hi Guys!

      New member and could really use your advice. I would have to believe this has been an issue for others but a search here came up with nothing......? (Probably me not doing search correctly)
       
      I have an 87 Big Bear 350 YFM350FWT
      The OEM Mikuni BTM carb is shot and would rather replace than rebuild.
      It is no longer made and I have had good luck with NICHE carbs so I ordered a #K-CRB-0006 This was what they said was replacement when ordered. This Carb only uses 1 Throttle cable. The Slide is linked so it uses one. (OEM had 2nd cable coming through top to move slide)
       
      Problem is when I ordered a replacement Cable from NICHE (#C-CBL-0061) the Cable wire is a little short, not allowing Throttle to return all the way down to Idle position. I called NICHE and they are at a loss. Haven't gotten back to me after 2+ weeks.
       
      What would you recommend other than a carb rebuild?
      Can I just use 1 of the OEM cables (It is the right length) and snip/disconnect the other that went to top of Carb for Slide?
      Or ??
       
      Thanks in advance for any advice you have!!
       
      Dave
×
×
  • Create New...