Quantcast
Jump to content


2003 Kawasaki Prairie 650 4X4 ATV Carburetor


burfordc

Recommended Posts

My front pipe is cool after running for a few seconds and the back one is really hot. It is running like crap and only if I keep the choke half open. The spark plug is firing up front. Here are my questions:

Do I have one or two carbs? It looks like 2.

I only see one fuel line off of the spit-cock to the carb in the back, does that feed them both?

Is there a fuel filter for each carb (If I have 2)?

Any ideas on what might be wrong?

Thank your for any help out there.

Link to comment
Share on other sites

Yes you have 2 carbs the fuel line comming from your off/on fuel cock should have a filter in the line before it goes to a T fitting & splits off to each carb. The carbs could need cleaned, You will be better off doing a search on adjusting the carbs you have fuel / air mixture screws that is adjustable the idle is just one knob that changes both carbs at the same time. Then their is the carb sync adjustment. In order to sync the carbs you need a carb sync tool. It gets the carbs matched up you can do a internet search on how to make a sync tool & on the steps to sync the carbs. I would read about it first to make sure it's something you could do. Syncing the carbs would be the last thing on a check list. You have to remove some of the plastics to be able to get to the carbs where you can see everything but check all the fuel lines , check the clamps that hold the carbs in the intake boots, air/fuel mixture screws I think it's around 2 full turns out from fully closed if you close these off to check them you just turn them till they stop you don't tighten them down or you will damage them. After this stuff is checked if it all seems to be good I would clean the carbs & reinstall them & check if their in sync. I hope this helps.

Link to comment
Share on other sites

they are a pain to take off ...lol.. i have dont this on several of the kawasaki V twin's ... its usually a dirty /clogged carb... get a can of chemtool carb cleaner and take them off and clean them out ... i would also change the filter while you are doing this ... i have found some filters start comming apart on the inside and let stuff get into the carbs and clog them on the V's i have 1 and most of my friends do also .. im the mechanic for our riding group and i get to do most of the work on all 9 of the V's in our riding group ... we also have several parts V's ...

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Forum Topics

    • By Spritee1
      having an issue with the unit when running under a load up a hill or in high gear, seems like the belt is slipping, there is a clapping sound coming from the primary clutch like it releases and snaps back in. i don't think I should have a noise like that. this is a friends unit and he has already replaced the primary twice with the same result.
      not sure where to look next
    • By justent_88
      Hello, im looking for some input on this situation i have. My 94 Mojave has no spark, and i have no idea what it is. Ive replaced/tested the magneto, the pickup coil, cdi, the ignition coil. Even the key and Killswitch. I haven't tested the harness its self, but i have tried another harness and still nothing. The only thing i can think of is the fly wheel itself. I have found a lot of metal shavings in the fly wheel and have cleaned it the best I could. But nothing happened afterwards. I am truly stumped here and hoping some of yous could shed some knowledge/ideas that could help get this thing to fire. 
    • By hardcastle
      My friends KQ 300 starts fine and runs, as soon as you put it in gear and try to accelerate its bucks and farts like crazy, not moving... I cleaned carb and it worked good for 1 day... now back to same problem.... could it be such as a bent valve????
    • By Mhatayas
      My uncle bought a Baja 250, 2006. Knew there was no spark since the get go. He don't know anything about quads so is getting me to help him try to get it running...
       
      battery is bad so I connected battery charger to it to crank it over , cranks over well , but no spark .... 
      Lights and everything work fine , but with each crank over using the e start switch , the display reads 999 888 777 666 ... Right down to 000 and repeats itself . 
       
      He managed to get a parts bike , I changed over the CDI and the coil and the stator from the parts bike and there was another black box by the voltage regulator I changed over ... I used my multimeter to confirm as much as I could works , it's hard without knowing which wires are which , and I cannot find any diagrams online for this bike ? 
       
      Do you think it could be the Killswitch? There's so many wires coming from there I don't know where to start . Also I should mention it appears the fan on the front of the bike has been taken off (the wires have been cut too ) 
       
      If this bike sparked it would run . The previous owner said he parked it one day and it just wouldn't start after.
    • Best Fit and Protection Guaranteed for all your cars, trucks, boats, jet-skis and more. Visit SealSkinCovers.com. Seal Skin Supreme Covers come with a Lifetime Warranty. Free Shipping!
    • By ethie
      Hi All
      I have a 2012 Coleman 500 Outfitter that keeps fouling out the plug within 10-15 minutes 
      not sure where to start
×
×
  • Create New...