Quantcast
Jump to content

Recommended Posts

Posted

I have a 300 fourtrax that kills on me after it runs for a little whill or after it warms up can any body help me .I think I have tried every thing but there has to be some thing that I have not tried.HELLLLLP!!!!!!!!

Posted

What is the Year,Make and Model of this.

And a bike will run on choke until it gets warm then it will die and it will cause it to backfire trying to start it. If the choke isn't on then check your air filter. Sounds like an air flow problem.

Posted

check to make shure it dosent have a vaccume leak on the intake boot....i have seen them have a crack or not seal very well and will do this once they warm up... it also could be vapor locking ... put a piece of wire around the fuel line ... wrap it around several times .... or use the old clothes pit trick

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Forum Topics

    • By Randel1
      I recently read an article about restoring or at least improving the looks of faded and discolored plastic body parts. In the article it suggested using a 50/50 mixture of boiled linseed oil and paint thinner. You mix it up and apply it with a brush or rag to rub it in and remove the oxidation. I curious to find out if anyone has had experience with doing this and what was their short/long term results of doing so. I would hate to try it and find out that a few weeks/months down the road my plastic body parts self destruct.   
    • By Atomusthenes
      I would appreciate being pointing in the correct direction for a wiring diagram and or schematics of the 88 Honda FourTrax 300 4x4 if anybody has any knowledge of how to test the ignition system stator and CDI I don't know if the voltage regulator probably and also the FCU I put a new ignition in it it is a cheap aftermarket one doesn't have the correct plugs but has the correct wiring scheme I get power  the neutral light comes on and the oil light stays on it turns over but I have no spark
    • By Memphis
      Not sure if in right place but here goes
      My 300 is lacking power only reaching 30mph and struggling uphill everything else seems ok other that this problem cleaned all fuel new filter pan and all new fuel pump and spark plug full oil change is there anything I am missing
      ps It is auto and does noy seem to want to get in another gear 5200 rpm at 30mph
       
      Regards
    • By P_syko
      I’m brand new to 4 wheelers and just bought a 1987 Yamaha Moto 4 350. It has good compression and fuel, but no spark. I’ve looked high and low trying to find how to test all the components of the ignition system, but can’t find anything. This has a new CDI box on it, but I suspect it might be the stator. How do I test the stator on this? Any help would be greatly appreciated! 
    • By carkivey3
      i just picked this up. was told ran fine but overheating issues led to replacing head gasket and head. has not ran since. he is not a mechanic but helped someone else who he could not get back to finish job, got aggravated and put up for sale. i was thinking timing issues. i have 110-120psi on all 3 cylinders so i think valves are correct. dont know about distributor yet. however i have no spark. i have no power going to ignition coil. tried to follow white wire but gets lost in wire harness. does anyone have a wiring diagram? can anyone tell me what conditions have to be met before starting. motor turns over so i would think all safeties are met but you never know.
×
×
  • Create New...